04-28-2004
omg haha i'm so so stuipd i'm sorry ...lol it was my fault, i was specifying hdb1 instead of hdb2, exams make me crazy...lol. I wondered though, I'm not the best with fdisk, how would i use the rest of my hd on a partition? i made a new one but i can't make it for the whole hard drive.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just finished installing Solaris 5.8 and I tried to install StarOffice, it said I was out of room. Now I have a 3 gig HD and I THOUGHT that I gave 512 to swap and kept the rest for storage room.
How do I check how much room I have, how would I if I figured out I don't have enough room add... (5 Replies)
Discussion started by: veitcha
5 Replies
2. UNIX for Advanced & Expert Users
I'm trying to compile and install both most recent version of 'make' and the
most recent version of 'openssh' on my Sparc20.
I've run into the following problems... and I don't know what they mean. Can
someone please help me resolve these issues?
I'm using the 'make' version that was... (5 Replies)
Discussion started by: xyyz
5 Replies
3. UNIX for Dummies Questions & Answers
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies
4. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
5. Solaris
Solaris 10 5/08 on Ultra 40 M2
It boots fine off primary disk but having issues booting off the mirror disk.
I get this error when booting off mirror disk:
Booting 'Solaris 10 ... Mirror disk'
root (hd1,0,a)
Error 22: No such partition
Press any key to continue...
Any... (7 Replies)
Discussion started by: etc
7 Replies
6. Shell Programming and Scripting
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
Discussion started by: jaysunn
6 Replies
7. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
8. Filesystems, Disks and Memory
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Discussion started by: edydsuranta
2 Replies
9. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
10. Debian
Hello, i'm trying to set up a machine with an encrypted filesystem. It's a Debian 9/i386.
The partition table on /dev/sda
1. 1 MiB BIOS BOOT (04) N/A N/A
2. 256 MiB Linux (83) ext4 /boot
3. 2304 MiB Linux (83) ext4 /
4. 1 MiB MINIX (81) N/A N/A
5. 510 MiB Linux... (7 Replies)
Discussion started by: tyuxar
7 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
chown(1), mknod(1), sd(4), mount(8)
COLOPHON
This page is part of release 3.44 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)