04-24-2004
Your answer is in your post. Go into fdisk and type "n" to create a new parition. It will prompt you for the info. After the prompts are done, type "w" to save and exit. Now run "mke2fs /dev/hdb2" followed by "mount /dev/hdb2 /somedir".
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just finished installing Solaris 5.8 and I tried to install StarOffice, it said I was out of room. Now I have a 3 gig HD and I THOUGHT that I gave 512 to swap and kept the rest for storage room.
How do I check how much room I have, how would I if I figured out I don't have enough room add... (5 Replies)
Discussion started by: veitcha
5 Replies
2. UNIX for Advanced & Expert Users
I'm trying to compile and install both most recent version of 'make' and the
most recent version of 'openssh' on my Sparc20.
I've run into the following problems... and I don't know what they mean. Can
someone please help me resolve these issues?
I'm using the 'make' version that was... (5 Replies)
Discussion started by: xyyz
5 Replies
3. UNIX for Dummies Questions & Answers
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies
4. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
5. Solaris
Solaris 10 5/08 on Ultra 40 M2
It boots fine off primary disk but having issues booting off the mirror disk.
I get this error when booting off mirror disk:
Booting 'Solaris 10 ... Mirror disk'
root (hd1,0,a)
Error 22: No such partition
Press any key to continue...
Any... (7 Replies)
Discussion started by: etc
7 Replies
6. Shell Programming and Scripting
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
Discussion started by: jaysunn
6 Replies
7. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
8. Filesystems, Disks and Memory
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Discussion started by: edydsuranta
2 Replies
9. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
10. Debian
Hello, i'm trying to set up a machine with an encrypted filesystem. It's a Debian 9/i386.
The partition table on /dev/sda
1. 1 MiB BIOS BOOT (04) N/A N/A
2. 256 MiB Linux (83) ext4 /boot
3. 2304 MiB Linux (83) ext4 /
4. 1 MiB MINIX (81) N/A N/A
5. 510 MiB Linux... (7 Replies)
Discussion started by: tyuxar
7 Replies
fd(4) Kernel Interfaces Manual fd(4)
NAME
fd - file descriptor files
DESCRIPTION
The /dev/fd file system is a pseudo-file system layered beneath the Virtual File System (VFS). The file descriptor files (fd*) are those
files that are accessible through file descriptors. The file descriptors use the naming convention /dev/fd/0, /dev/fd/1, /dev/fd/2 and so
on up to any number.
To make the /dev/fd file system known to the operating system, you must create the directory with the correct privileges, then you must
mount the file system. The following steps describe how to create the directory, mount the file system both manually and automatically,
and how to dismount the file system: Create the directory using the mkdir and chmod commands: mkdir /dev/fd; chmod 777 /dev/fd Mount the
file system manually using the mount command: mount -t fdfs /dev/fd /dev/fd Mount the file system automatically by editing either the
/etc/fstab file or the /sbin/bcheckrc file.
Add the following entry to the /etc/fstab file: /dev/fd /dev/fd fdfs rw 0 0 This entry mounts the pseudodevice /dev/fd on the
/dev/fd directory with read/write privileges. The file system type is fdfs and the zeros (0) in the remaining fields specify that
the file system is not to be backed up nor can file system checks be performed by the fsck command as this is a virtual file system.
Add the following entry to the /sbin/bcheckrc file: # # mount fdfs # echo 'Mounting /dev/fd filesystem' /sbin/mount -a -v -t fdfs
Again, the /dev/fd file system should not be mounted in this manner if an entire system is to be backed up starting from the root
directory. Dismount the file system using the umount command: umount /dev/fd For correct truncate() behavior on fd files, you must
load your program using the -lsys5 flag.
RESTRICTIONS
The /dev/fd file descriptors should not be exported.
EXAMPLES
The following example show how the open and dup functions have the same effect if file descriptor n is opened:
fd = open("/dev/fd/n", mode);
fd = dup(n);
In the above example, the open function is equal to the creat function and mode is ignored. Using the dup function, subsequent reads or
writes on the fd file descriptor files fail unless the original file descriptor enables the operation.
ERRORS
The following error condition exists: The file descriptor is not valid.
RELATED INFORMATION
Commands: chmod(1), mkdir(1), mount(8).
Functions: creat(2), dup(2), open(2). delim off
fd(4)