04-23-2004
I think you are talking about /boot. I typically make this 512 MB which is overkill but I like to have room to play. This just stores the basic boot stuff. On some systems if /boot (or / if you didn't create a seperate /boot partition) is over 4 GB the system will not boot. It's a bios thing. With a small /boot you could create a huge / and not have to worry about boot problems. I usually use ext3 but ext2 works just fine as well.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just finished installing Solaris 5.8 and I tried to install StarOffice, it said I was out of room. Now I have a 3 gig HD and I THOUGHT that I gave 512 to swap and kept the rest for storage room.
How do I check how much room I have, how would I if I figured out I don't have enough room add... (5 Replies)
Discussion started by: veitcha
5 Replies
2. UNIX for Advanced & Expert Users
I'm trying to compile and install both most recent version of 'make' and the
most recent version of 'openssh' on my Sparc20.
I've run into the following problems... and I don't know what they mean. Can
someone please help me resolve these issues?
I'm using the 'make' version that was... (5 Replies)
Discussion started by: xyyz
5 Replies
3. UNIX for Dummies Questions & Answers
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies
4. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
5. Solaris
Solaris 10 5/08 on Ultra 40 M2
It boots fine off primary disk but having issues booting off the mirror disk.
I get this error when booting off mirror disk:
Booting 'Solaris 10 ... Mirror disk'
root (hd1,0,a)
Error 22: No such partition
Press any key to continue...
Any... (7 Replies)
Discussion started by: etc
7 Replies
6. Shell Programming and Scripting
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
Discussion started by: jaysunn
6 Replies
7. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
8. Filesystems, Disks and Memory
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Discussion started by: edydsuranta
2 Replies
9. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
10. Debian
Hello, i'm trying to set up a machine with an encrypted filesystem. It's a Debian 9/i386.
The partition table on /dev/sda
1. 1 MiB BIOS BOOT (04) N/A N/A
2. 256 MiB Linux (83) ext4 /boot
3. 2304 MiB Linux (83) ext4 /
4. 1 MiB MINIX (81) N/A N/A
5. 510 MiB Linux... (7 Replies)
Discussion started by: tyuxar
7 Replies
LEARN ABOUT OPENDARWIN
findfs
FINDFS(8) System Administration FINDFS(8)
NAME
findfs - find a filesystem by label or UUID
SYNOPSIS
findfs NAME=value
DESCRIPTION
findfs will search the block devices in the system looking for a filesystem or partition with specified tag. The currently supported tags
are:
LABEL=<label>
Specifies filesystem label.
UUID=<uuid>
Specifies filesystem UUID.
PARTUUID=<uuid>
Specifies partition UUID. This partition identifier is supported for example for GUID Partition Table (GPT) partition tables.
PARTLABEL=<label>
Specifies partition label (name). The partition labels are supported for example for GUID Partition Table (GPT) or MAC partition
tables.
If the filesystem or partition is found, the device name will be printed on stdout.
The complete overview about filesystems and partitions you can get for example by
lsblk --fs
partx --show <disk>
blkid
EXIT STATUS
0 success
1 label or uuid cannot be found
2 usage error, wrong number of arguments or unknown option
AUTHOR
findfs was originally written by Theodore Ts'o <tytso@mit.edu> and re-written for the util-linux package by Karel Zak <kzak@redhat.com>.
ENVIRONMENT
LIBBLKID_DEBUG=all
enables libblkid debug output.
SEE ALSO
blkid(8), lsblk(8), partx(8)
AVAILABILITY
The findfs command is part of the util-linux package and is available from Linux Kernel Archive <https://www.kernel.org/pub/linux/utils
/util-linux/>.
util-linux March 2014 FINDFS(8)