04-22-2004
Normal! You can use PQMagic to Creat a New Partion. With RH9, Wizard will help you creat partion for Linux (Ext2, Ext3, Swap....). To run RH9, you need have 4 GB HD for 2 partion of Linux:
- Ext2 or Ext3 (Partion Data of Linux)
- Swap (Partion Virtual Memory of Linux).
It's very simple.
Or you can do this work by command:
To creat ext2 partion:
mke2fs -c <partion> <size>
To creat swap partion:
mkswap -c <partion> <size>
Good Luck
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just finished installing Solaris 5.8 and I tried to install StarOffice, it said I was out of room. Now I have a 3 gig HD and I THOUGHT that I gave 512 to swap and kept the rest for storage room.
How do I check how much room I have, how would I if I figured out I don't have enough room add... (5 Replies)
Discussion started by: veitcha
5 Replies
2. UNIX for Advanced & Expert Users
I'm trying to compile and install both most recent version of 'make' and the
most recent version of 'openssh' on my Sparc20.
I've run into the following problems... and I don't know what they mean. Can
someone please help me resolve these issues?
I'm using the 'make' version that was... (5 Replies)
Discussion started by: xyyz
5 Replies
3. UNIX for Dummies Questions & Answers
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies
4. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
5. Solaris
Solaris 10 5/08 on Ultra 40 M2
It boots fine off primary disk but having issues booting off the mirror disk.
I get this error when booting off mirror disk:
Booting 'Solaris 10 ... Mirror disk'
root (hd1,0,a)
Error 22: No such partition
Press any key to continue...
Any... (7 Replies)
Discussion started by: etc
7 Replies
6. Shell Programming and Scripting
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
Discussion started by: jaysunn
6 Replies
7. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
8. Filesystems, Disks and Memory
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Discussion started by: edydsuranta
2 Replies
9. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
10. Debian
Hello, i'm trying to set up a machine with an encrypted filesystem. It's a Debian 9/i386.
The partition table on /dev/sda
1. 1 MiB BIOS BOOT (04) N/A N/A
2. 256 MiB Linux (83) ext4 /boot
3. 2304 MiB Linux (83) ext4 /
4. 1 MiB MINIX (81) N/A N/A
5. 510 MiB Linux... (7 Replies)
Discussion started by: tyuxar
7 Replies
LEARN ABOUT REDHAT
swapon
SWAPON(8) Linux Programmer's Manual SWAPON(8)
NAME
swapon, swapoff - enable/disable devices and files for paging and swapping
SYNOPSIS
/sbin/swapon [-h -V]
/sbin/swapon -a [-v] [-e]
/sbin/swapon [-v] [-p priority] specialfile ...
/sbin/swapon [-s]
/sbin/swapoff [-h -V]
/sbin/swapoff -a
/sbin/swapoff specialfile ...
DESCRIPTION
Swapon is used to specify devices on which paging and swapping are to take place. Calls to swapon normally occur in the system multi-user
initialization file /etc/rc making all swap devices available, so that the paging and swapping activity is interleaved across several
devices and files.
Normally, the first form is used:
-h Provide help
-V Display version
-s Display swap usage summary by device. Equivalent to "cat /proc/swaps". Not available before Linux 2.1.25.
-a All devices marked as ``swap'' swap devices in /etc/fstab are made available. Devices that are already running as swap are silently
skipped.
-e When -a is used with swapon, -e makes swapon silently skip devices that do not exist.
-p priority
Specify priority for swapon. This option is only available if swapon was compiled under and is used under a 1.3.2 or later kernel.
priority is a value between 0 and 32767. See swapon(2) for a full description of swap priorities. Add pri=value to the option field
of /etc/fstab for use with swapon -a.
Swapoff disables swapping on the specified devices and files. When the -a flag is given, swapping is disabled on all known swap devices
and files (as found in /proc/swaps or /etc/fstab).
NOTE
You should not use swapon on a file with holes. Swap over NFS may not work.
SEE ALSO
swapon(2), swapoff(2), fstab(5), init(8), mkswap(8), rc(8), mount(8)
FILES
/dev/hd?? standard paging devices
/dev/sd?? standard (SCSI) paging devices
/etc/fstab ascii filesystem description table
HISTORY
The swapon command appeared in 4.0BSD.
Linux 1.x 25 September 1995 SWAPON(8)