08-07-2001
no i don't hear the modem...
as far as the AT commands goes...i have no idea. this is my first day using linux...
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hello :(
i have just installed linux mandrake 7.1 and i've been trying to get help EVERYWHERE!! i can't get on the internet.
it dials the modem and connects but when i try and go 2 any web pages it gets no further than looking for the server.
plleeeeeeeeeeeeeeeeeeeeeease help
thanks,... (7 Replies)
Discussion started by: mipsy
7 Replies
2. UNIX for Dummies Questions & Answers
for those who have read my earlier posts i have been trying for about a week and a half to get my internet connection working with no results...
my isp is ex-pressnet (in VA)...one-way cable internet service (dial-up for uploads, cable for downloads) using a com21 cable modem...this is extremly... (6 Replies)
Discussion started by: justchillin
6 Replies
3. Shell Programming and Scripting
I wonder how I shall read the result below, especially 'what'
shown below.
The result was shown when I entered 'w'.
E.g what is TOP? What is gosh ( what does selmgr mean?)?
login@ idle JCPU PCPU what
6:15am 7:04 39 39 TOP
6:34am 6:45 45 45 TOP
6:41am ... (1 Reply)
Discussion started by: Aelgen
1 Replies
4. UNIX for Dummies Questions & Answers
I running HPUX 11.0,
Netscape gives me an error "Unable to locate Server" when using a www.something.com address.
If I use an IP address I get past the router and onto the Internet.
My workstation can get to the Router @ 192.168.0.1 and also it's local APACHE server.
I have DHCP enabled... (8 Replies)
Discussion started by: johnalt
8 Replies
5. Solaris
ive installed a fresh copy of solaris 10 on a E3500 Server machine, i gave it a static IP address , 192.168.1.15 its a test server in our office (small office) we are using LINKSYS as our internet router and DHCP as well .. its IP is 192.168.1.1 and ive added this IP as Default route on the server... (9 Replies)
Discussion started by: mduweik
9 Replies
6. Solaris
i have just installed solaris 10 on a 60 gb hard drive. now im trying to install my nic driver but when i put in the floppy disk for the nic card it cant read it, so then i found that i have to mount the floppy drive and i tried putting in the mount command but i dont know where to mount it and if... (38 Replies)
Discussion started by: vutty81
38 Replies
7. Solaris
Hi I installed solaris developer edition 1/08 today.I want to connect to Broadband internet through my ADSL 2+ Modem/Router with a username and password.
plz help in this case,I am new to sun solaris:confused:
the modem itself is a router it worked well on ubuntu and red hat (3 Replies)
Discussion started by: santugvd
3 Replies
8. Linux
HI,
Am using GPRS ( MOB # 3230 ) internet connection in windows
Hw to use internet r connect in linux.. ( Red Hat Linux Ver.10 )
Please help me..
Thanks in adv.. (1 Reply)
Discussion started by: bharath raja
1 Replies
9. Solaris
Dear freinds...
I downloaded solaris for x86 and was able to configure the lan correctly.. I can ping and share with other destops through lan... but still I can't connect to internet ? can you please help..
I put my default gateway which is 192.168.1.1 to /etc/defaultrouter but with no use..... (13 Replies)
Discussion started by: yahyaaa
13 Replies
10. Linux
Hi,
Can someone guide me regarding how to connect to internet.
what are steps?
Thanks in advance (2 Replies)
Discussion started by: naren nandale
2 Replies
TERM(1) General Commands Manual TERM(1)
NAME
term - turn PC into a dumb terminal [IBM]
SYNOPSIS
term [baudrate] [parity] [bits_per_character] [-dial_string] [device]
EXAMPLES
term 2400 # Talk to modem at 2400 baud
term 1200 7 even # 1200 baud, 7 bits/char, even parity
term 8 9600 /dev/tty01
# 9600 baud, 8 bits/char, no parity, use tty01
term -atdt12345 /dev/tty01
# Start with a command to dial out
DESCRIPTION
Term allows MINIX to talk to a terminal or modem over RS232 port 1. The program first sets the baudrate, parity and character length, and
then forks. The parent sits in a loop copying from stdin (usually the console's keyboard), to the terminal or modem (/dev/tty00). The
child sits in a loop copying from the terminal or modem (/dev/tty00) to standard output. Thus when RS232 port 1 is connected to a modem,
every keystroke typed on the keyboard is sent to the modem, and every character arriving from the modem is displayed. Standard input and
output may be redirected, to provide a primitive file transfer program, with no checking. Any argument that starts with a minus ('-') is
sent out to the modem, usually to dial out. Term accepts several commands that are formed by typing the escape character, CTRL-], and a
letter. Type CTRL-]? to see a list of commands. The subshell command is very important, it allows you to type in a ZMODEM command to
transfer data. Do not quit term to do this, or your modem line will be reset! Term keeps the modem line open on file descriptor 9 while
running the subshell, so you can type
<&9 >&9
at the end of your ZMODEM command to connect it to the modem.
Important note: to use term, it is essential that /etc/ttytab is configured so that there is no shell hanging on /dev/tty01. If there is,
both the shell and term will try to read from /dev/tty01, and nothing will work.
SEE ALSO
rz(1), sz(1).
TERM(1)