04-16-2004
well first, post the script that you have already written. then we can go from there. very rarely will you find someone who has the time to write out a script for you, especially if you are not willing to write one out on your own. not only that, but it can be insulting asking people to do work for you. were here to help, not to do work for you.
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
When I pinged a machin, I got to be seen a different kind of
reply from that machine.
This is as below : "Reply from 136.128.11.116: Source quench received." Which I felt like an un-usual message.
So what does this mean.
Regards & Thanks in advance.
Vishwa. (4 Replies)
Discussion started by: S.Vishwanath
4 Replies
2. UNIX for Dummies Questions & Answers
Hi there hope list can help
I'm looking for a command that does the following
lets say i ping a server 00.00.000.00
and this server is up and running how do i get the ping command to return a UP or a Down
meaning
if the command is true do this
if the command is False do this
... (2 Replies)
Discussion started by: nemex
2 Replies
3. AIX
We can ping out but the return never comes back even to localhost
ping localhost
PING loopback: (127.0.0.1): 56 data bytes
64 bytes from 127.0.0.1: icmp_seq=0 ttl=255 time=0 ms
it just sits there....
any ideas, any files to check (1 Reply)
Discussion started by: csaunders
1 Replies
4. UNIX for Dummies Questions & Answers
Hi ,
I have one system installed on Linux Red Hat 3.0. I have ip of system 3.156.168.*** and i want to ping some port that is on this IP which command i can do this?
sam70 (1 Reply)
Discussion started by: sam70
1 Replies
5. Linux
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies
6. IP Networking
I have an old MP-Ras Unix system. I have setup netowkring but am unable to ping any local network pcs or the default gateway. If i use the arp -a command I receive the correct mac address for all connected pcs but I cannot ping anything except the local address. Any help would be appreciative.
... (7 Replies)
Discussion started by: Rutgerncas
7 Replies
7. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
8. IP Networking
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies
9. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
LEARN ABOUT DEBIAN
maria-vis
MARIA-VIS(1) General Commands Manual MARIA-VIS(1)
NAME
maria-vis - graph visualization script for maria
SYNOPSIS
maria-vis
DESCRIPTION
This manual page documents briefly the maria-vis command.
maria-vis is a lefty script invoked by maria in order to visually present information to the user. The script reads commands and direc-
tives from standard input and may write maria query language commands to standard output. An end-of-file condition on standard input ter-
minates the script.
The script is built on top of the dotty script that is part of the GraphViz package. The commands prefixed with visual in maria issue two
kinds of commands to this script: new(); or add(); followed by a newline character and a graph definition in the dot input language. The
new function in the script displays the graph in a new window, while the add function copies information from the graph to the last modi-
fied graph.
SEE ALSO
dot(1), dotty(1), lefty(1), maria(1).
AUTHOR
This manual page was written by Marko Makela <msmakela@tcs.hut.fi>. The maria-vis script and the visualization option were designed and
implemented by Marko Makela. Please see the copyright file in /usr/share/doc/maria for details.
August 10, 2001 MARIA-VIS(1)