04-16-2004
Go to single user mode and check /etc/rc.config.d/netconf. Be sure that the hostname and ip addresses are correct. Check /etc/hosts to be sure that you have the right hostname and ip address there as well.
10 More Discussions You Might Find Interesting
1. HP-UX
This will most likely be a real dumb question for a HP-UX admin, but here it goes anyhow.
lan0 - is up and configured
lan1 - is down, I want to bring it up.
lanconfig....ifconfig is there a difference?
My real question is, in solaris there is an /etc/hostname."?" file, is there a... (4 Replies)
Discussion started by: viRaven
4 Replies
2. OS X (Apple)
Hi,
I type (as root) "ifconfig en1 ether aa:aa: " but it doesnt change the mac of my airport. Can anyone help me?
Thx. (0 Replies)
Discussion started by: Jariya
0 Replies
3. Shell Programming and Scripting
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
Discussion started by: moco
3 Replies
4. UNIX for Dummies Questions & Answers
hey,
I know that ifconfig on linux systems is identical to win ipconfig.
I wanted to know if there is a linux distribution (new or old) that uses the ipconfig command.
thanks alot :) (2 Replies)
Discussion started by: tsmotix
2 Replies
5. Solaris
Hi All,
I logged into a sun microsystems server box, using both a vnc session and a ssh session. I am able to use "ifconfig -a" in a ssh session, but the same on a vnc session says that its a invalid command. how is this possible, when i am logging into the same box through two different... (4 Replies)
Discussion started by: pardhuhere
4 Replies
6. IP Networking
Hi all,,i have problem with my homework form my lecture..
He is give me a homework to create:
ifconfig eth0 0.255.255.255 1.1.168.192
my lecture says, i can making the shell scripting to finish my homework..
i have question, can setting ifconfig like in the upper? (1 Reply)
Discussion started by: demhyt
1 Replies
7. IP Networking
Hi all,
I am getting some error messages during bootup
ifconfig :<hostname> bad address
and some more messages related to it.
I some how checked the /etc/hostanem.hme0 /etc/hosts file.
Entries in these files were proper.
If I am running the following command from root:
... (5 Replies)
Discussion started by: amit_sapre
5 Replies
8. Linux
Hi All,
I need some info on ifconfig.
ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux.
1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Discussion started by: ahamed101
2 Replies
9. Shell Programming and Scripting
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
Discussion started by: mail2sant
3 Replies
10. Solaris
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies
LEARN ABOUT REDHAT
host.conf
HOST.CONF(5) Linux System Administration HOST.CONF(5)
NAME
host.conf - resolver configuration file
DESCRIPTION
The file /etc/host.conf contains configuration information specific to the resolver library. It should contain one configuration keyword
per line, followed by appropriate configuration information. The keywords recognized are order, trim, multi, nospoof, and reorder. These
keywords are described below.
order This keyword specifies how host lookups are to be performed. It should be followed by one or more lookup methods, separated by com-
mas. Valid methods are bind, hosts, and nis.
trim This keyword may be listed more than once. Each time it should be followed by a single domain name, with the leading dot. When
set, the resolv+ library will automatically trim the given domain name from the end of any hostname resolved via DNS. This is
intended for use with local hosts and domains. (Related note: trim will not affect host- names gathered via NIS or the hosts file.
Care should be taken to ensure that the first hostname for each entry in the hosts file is fully qualified or non-qualified, as
appropriate for the local installation.)
multi Valid values are on and off. If set to on, the resolv+ library will return all valid addresses for a host that appears in the
/etc/hosts file, instead of only the first. This is off by default, as it may cause a substantial performance loss at sites with
large hosts files.
nospoof
Valid values are on and off. If set to on, the resolv+ library will attempt to prevent hostname spoofing to enhance the security of
rlogin and rsh. It works as follows: after performing a host address lookup, resolv+ will perform a hostname lookup for that
address. If the two hostnames do not match, the query will fail.
spoofalert
If this option is set to on and the nospoof option is also set, resolv+ will log a warning of the error via the syslog facility.
The default value is off.
reorder
Valid values are on and off. If set to on, resolv+ will attempt to reorder host addresses so that local addresses (i.e., on the
same subnet) are listed first when a gethostbyname(3) is performed. Reordering is done for all lookup methods. The default value
is off.
FILES
/etc/host.conf
Resolver configuration file
/etc/resolv.conf
Resolver configuration file
/etc/hosts
Local hosts database
SEE ALSO
gethostbyname(3), hostname(7), resolv+(8), named(8)
Debian GNU/Linux 1997-01-02 HOST.CONF(5)