04-16-2004
I just found an old hp box with btlan4 in operation! I had a rough time finding the files, this driver didn't have "LAN" in it's product name. I got the files with:
swlist -l file 100BT-GSC\*
which isn't exactly obvious.
There is no hostname.btlan4 there and we don't that file on our box. This would imply that someone may have customized your setup.
Had you followed HP's standard, you would need to modify two files both in /etc/rc.config.d The first is netconf which is where you set the ip address, netmask, and other general IP stuff. And there is hpgsc100conf which is where you set any btlan4 specific parameters.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I asked a similar question earlier and got a very good answer but a new doubt came up. This is a few lines of a '/sbin/ifconfig' command on my PC:
RX packets:3781025 errors:0 dropped:0 overruns:0 frame:0
TX packets:1941909 errors:0 dropped:0 overruns:0 carrier:0
Does the RX and TX packets... (1 Reply)
Discussion started by: mint1981
1 Replies
2. UNIX for Dummies Questions & Answers
I have to cd into /sbin in order to use ifconfig to check out my network cards. This has only started to happen since I downloaded the last update from RedHat(The machine runs RedHat 8.0).
Does anyone know what happened?
More importantly, are there any sources that can help me with this... (3 Replies)
Discussion started by: Jody
3 Replies
3. UNIX for Dummies Questions & Answers
SunOS Release 5.7.
Original ifconfig -a output:
pnt0: flags=863<UP, BROADCAST,NOTRAILERS........
inet 10.2.34.49 netmask fffffe00 broadcast 10.2.34.255 ...
Attempted to change ip address for pnt0. Typed the following command and forgot the "netmask"
"ifconfig pnt0 10.2.35.49... (1 Reply)
Discussion started by: forbin24
1 Replies
4. UNIX for Dummies Questions & Answers
I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
Discussion started by: breigner
7 Replies
5. OS X (Apple)
Hi,
I type (as root) "ifconfig en1 ether aa:aa: " but it doesnt change the mac of my airport. Can anyone help me?
Thx. (0 Replies)
Discussion started by: Jariya
0 Replies
6. Solaris
On prior versions to solaris 10 when I want to add/change the IP address of an interface I will use this command.
ifconfig eri0 down
ifconfig eri0 192.xxx.xxx.xxx netmask 255.xxx.xxx.xxx up
then change /etc/hosts so that /etc/hostname.eri0 picks up on the correct IP.
I strange thing... (2 Replies)
Discussion started by: sparcguy
2 Replies
7. Shell Programming and Scripting
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
Discussion started by: moco
3 Replies
8. UNIX for Dummies Questions & Answers
hey,
I know that ifconfig on linux systems is identical to win ipconfig.
I wanted to know if there is a linux distribution (new or old) that uses the ipconfig command.
thanks alot :) (2 Replies)
Discussion started by: tsmotix
2 Replies
9. IP Networking
Hi all,
I am getting some error messages during bootup
ifconfig :<hostname> bad address
and some more messages related to it.
I some how checked the /etc/hostanem.hme0 /etc/hosts file.
Entries in these files were proper.
If I am running the following command from root:
... (5 Replies)
Discussion started by: amit_sapre
5 Replies
10. Shell Programming and Scripting
Hi there, I have a script which loops through the physical interfaces of a box and populates a variable called $NIC with the interface name
so if for example $NIC is equal to "e1000g0", I am trying to figure out some awk that will get the IP for that interface from ifconfig output
lo0:... (9 Replies)
Discussion started by: rethink
9 Replies
PUSH(8) BSD System Manager's Manual PUSH(8)
NAME
push -- fetch mail via POP
SYNOPSIS
push [-5 | --krb5] [-v | --verbose] [-f | --fork] [-l | --leave] [--from] [-c | --count] [--headers=headers] [-p port-spec |
--port=port-spec] po-box filename
DESCRIPTION
push retrieves mail from the post office box po-box, and stores the mail in mbox format in filename. The po-box can have any of the follow-
ing formats:
'hostname:username'
'po:hostname:username'
'username@hostname'
'po:username@hostname'
'hostname'
'po:username'
If no username is specified, push assumes that it's the same as on the local machine; hostname defaults to the value of the MAILHOST environ-
ment variable.
Supported options:
-5, --krb5
use Kerberos 5 (if compiled with support for Kerberos 5)
-f, --fork
fork before starting to delete messages
-l, --leave
don't delete fetched mail
--from behave like from.
-c, --count
first print how many messages and bytes there are.
--headers=headers
a list of comma-separated headers that should get printed.
-p port-spec, --port=port-spec
use this port instead of the default 'kpop' or '1109'.
The default is to first try Kerberos 5 authentication and then, if that fails, Kerberos 4.
ENVIRONMENT
MAILHOST
points to the post office, if no other hostname is specified.
EXAMPLES
$ push cornfield:roosta ~/.emacs-mail-crash-box
tries to fetch mail for the user roosta from the post office at ``cornfield'', and stores the mail in ~/.emacs-mail-crash-box (you are using
Gnus, aren't you?)
$ push --from -5 havregryn
tries to fetch From: lines for current user at post office ``havregryn'' using Kerberos 5.
SEE ALSO
from(1), pfrom(1), movemail(8), popper(8)
HISTORY
push was written while waiting for movemail to finish getting the mail.
HEIMDAL
May 31, 1998 HEIMDAL