04-16-2004
edit the /etc/host file with the new IP address.
Then reboot!
Also you may need to change the /etc/hostname.xxx files. You shoudln't but might want to look.
:-)
10 More Discussions You Might Find Interesting
1. HP-UX
This will most likely be a real dumb question for a HP-UX admin, but here it goes anyhow.
lan0 - is up and configured
lan1 - is down, I want to bring it up.
lanconfig....ifconfig is there a difference?
My real question is, in solaris there is an /etc/hostname."?" file, is there a... (4 Replies)
Discussion started by: viRaven
4 Replies
2. OS X (Apple)
Hi,
I type (as root) "ifconfig en1 ether aa:aa: " but it doesnt change the mac of my airport. Can anyone help me?
Thx. (0 Replies)
Discussion started by: Jariya
0 Replies
3. Shell Programming and Scripting
why the ifconfig command is not working in my machine?
it says "-bash: ifconfig: command not found"
why its says that?
actually i m looking for "how can I know the Network Interface Card physical address?"
Requesting u all for help.
thanks (3 Replies)
Discussion started by: moco
3 Replies
4. UNIX for Dummies Questions & Answers
hey,
I know that ifconfig on linux systems is identical to win ipconfig.
I wanted to know if there is a linux distribution (new or old) that uses the ipconfig command.
thanks alot :) (2 Replies)
Discussion started by: tsmotix
2 Replies
5. Solaris
Hi All,
I logged into a sun microsystems server box, using both a vnc session and a ssh session. I am able to use "ifconfig -a" in a ssh session, but the same on a vnc session says that its a invalid command. how is this possible, when i am logging into the same box through two different... (4 Replies)
Discussion started by: pardhuhere
4 Replies
6. IP Networking
Hi all,,i have problem with my homework form my lecture..
He is give me a homework to create:
ifconfig eth0 0.255.255.255 1.1.168.192
my lecture says, i can making the shell scripting to finish my homework..
i have question, can setting ifconfig like in the upper? (1 Reply)
Discussion started by: demhyt
1 Replies
7. IP Networking
Hi all,
I am getting some error messages during bootup
ifconfig :<hostname> bad address
and some more messages related to it.
I some how checked the /etc/hostanem.hme0 /etc/hosts file.
Entries in these files were proper.
If I am running the following command from root:
... (5 Replies)
Discussion started by: amit_sapre
5 Replies
8. Linux
Hi All,
I need some info on ifconfig.
ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux.
1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Discussion started by: ahamed101
2 Replies
9. Shell Programming and Scripting
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
Discussion started by: mail2sant
3 Replies
10. Solaris
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies
LEARN ABOUT FREEBSD
epair
EPAIR(4) BSD Kernel Interfaces Manual EPAIR(4)
NAME
epair -- A pair of virtual back-to-back connected Ethernet interfaces
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device epair
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_epair_load="YES"
DESCRIPTION
The epair is a pair of Ethernet-like software interfaces, which are connected back-to-back with a virtual cross-over cable.
Each epair interface pair is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or
using the cloned_interfaces variable in rc.conf(5). While for cloning you only give either epair or epair<n> the epair pair will be named
like epair<n>[ab]. This means the names of the first epair interfaces will be epair0a and epair0b.
Like any other Ethernet interface, an epair needs to have a network address. Each epair will be assigned a locally administered address by
default, that is only guaranteed to be unique within one network stack. To change the default addresses one may use the SIOCSIFADDR ioctl(2)
or ifconfig(8) utility.
The basic intend is to provide connectivity between two virtual network stack instances. When connected to a if_bridge(4) one end of the
interface pair can also be part of another (virtual) LAN. As with any other Ethernet interface one can configure vlan(4) support on top of
it.
SEE ALSO
ioctl(2), altq(4), bpf(4), if_bridge(4), vlan(4), loader.conf(5), rc.conf(5), ifconfig(8)
HISTORY
The epair interface first appeared in FreeBSD 8.0.
AUTHORS
The epair interface was written by Bjoern A. Zeeb, CK Software GmbH, under sponsorship from the FreeBSD Foundation.
BSD
July 26, 2009 BSD