04-16-2004
It's probably easiest to do it during the install. Burn the isos to CD, start the install, and either select auto partition, disk druid (my preference), or fdisk. If you currently have linux working on the system, 'dmesg | grep hd' will list the ide drives, 'dmesg |grep ida' will show the drives if you have a proliant box, and 'dmesg |grep sd' will show the SCSI drives. You can then use fdisk to partition them and mkfs or mke2fs to format them. However, during the install you will have to redo much of this anyway because the installer will not know which partition is for which mount point. Bottom line, just do it during the install.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I just finished installing Solaris 5.8 and I tried to install StarOffice, it said I was out of room. Now I have a 3 gig HD and I THOUGHT that I gave 512 to swap and kept the rest for storage room.
How do I check how much room I have, how would I if I figured out I don't have enough room add... (5 Replies)
Discussion started by: veitcha
5 Replies
2. UNIX for Advanced & Expert Users
I'm trying to compile and install both most recent version of 'make' and the
most recent version of 'openssh' on my Sparc20.
I've run into the following problems... and I don't know what they mean. Can
someone please help me resolve these issues?
I'm using the 'make' version that was... (5 Replies)
Discussion started by: xyyz
5 Replies
3. UNIX for Dummies Questions & Answers
hi,
1) is logical partition the same as physical partition except that one is physical and the other is logical?
2) then it must a one to one ratio? (3 Replies)
Discussion started by: yls177
3 Replies
4. UNIX for Dummies Questions & Answers
I've created a partition with GNU Parted, how do I mount the partition?
The manual information at http://www.gnu.org/software/parted/manual/parted.html is good, but I am sure about how I mount the partition afterwards.
Thanks,
--Todd (1 Reply)
Discussion started by: jtp51
1 Replies
5. Solaris
Solaris 10 5/08 on Ultra 40 M2
It boots fine off primary disk but having issues booting off the mirror disk.
I get this error when booting off mirror disk:
Booting 'Solaris 10 ... Mirror disk'
root (hd1,0,a)
Error 22: No such partition
Press any key to continue...
Any... (7 Replies)
Discussion started by: etc
7 Replies
6. Shell Programming and Scripting
Gentleman,
Please move if I have chose the incorrect forum section. I am trying to move data that is not backed up from partition 1 to partition 2 on a SAN that has a GFS2 filesystem. Since the data is not backed up I am rsyncing this data and once verified I will delete from the source... (6 Replies)
Discussion started by: jaysunn
6 Replies
7. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
8. Filesystems, Disks and Memory
Hi Experts
I would like to know different between soft partition concept and hard partition concept on solaris.
Here is little explanation between soft partition concept and hard partition concept on solaris.
Soft Partition:
1TB total space available in storage in all mapped to the OS to... (2 Replies)
Discussion started by: edydsuranta
2 Replies
9. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
10. Debian
Hello, i'm trying to set up a machine with an encrypted filesystem. It's a Debian 9/i386.
The partition table on /dev/sda
1. 1 MiB BIOS BOOT (04) N/A N/A
2. 256 MiB Linux (83) ext4 /boot
3. 2304 MiB Linux (83) ext4 /
4. 1 MiB MINIX (81) N/A N/A
5. 510 MiB Linux... (7 Replies)
Discussion started by: tyuxar
7 Replies
HUH(1) General Commands Manual HUH(1)
NAME
huh - redisplay last telegram received.
SYNOPSIS
huh [-sk]
DESCRIPTION
Huh reprints the last telegram that was sent to you. It is intended for use when telegrams get garbled on your screen.
Huh will only work if you had the ``record'' flag turned on when the telegram was received. This flag can be turned on with the mesg(1)
command.
Normally, huh will delete each message immediately after displaying it. If the -k flag is given, the message is non deleted, and the next
huh command will display it again. On the other hand, the -s flag suppresses the display of the message, so it will just be deleted.
Normally, only the last message is retained, except when amin(1) is run with the -p flag.
AUTHOR
Jan Wolter
FILES
~/.lastmesg
/etc/wrttmp
SEE ALSO
mesg(1), write(1), amin(1)
7th Edition Jan 20, 2000 HUH(1)