01-27-2004
The system info is Sun Fire V120 (UltraSPARC-IIe 648MHz), with 1024 MB RAM.
The reason I did a probe-scsi-all was that mt - f /dev/rmt/0 status said no device found. I tried shutting down with
sync; init 0
and probe-scsi-all seemd to better like it.
ok probe-scsi-all
/pci@1f,0/pci@1/scsi@8,1
/pci@1f,0/pci@1/scsi@8
Target 0
Unit 0 Disk SEAGATE ST336607LSUN36G 0307
Target 1
Unit 0 Disk SEAGATE ST336607LSUN36G 0307
ok
and when I do a boot -r the following error is given
NG: /pci@1f,0/pci@1/scsi@8,1 (glm1):
SCSI bus DATA IN phase parity error
WARNING: /pci@1f,0/pci@1/scsi@8,1 (glm1):
SCSI bus DATA IN phase parity error
WARNING: forceload of misc/md_trans failed
WARNING: forceload of misc/md_raid failed
WARNING: forceload of misc/md_hotspares failed
WARNING: forceload of misc/md_sp failed
configuring IPv4 interfaces: eri0 eri1.
As far as I am aware nothing has changed, any ideas?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Can someone please.... help me how to install tape backup
I am using FreeBSD Unix version running on I386 PC box. My IDE tape device is made by HP (Colorado 5GB).
Thank you in advance! (15 Replies)
Discussion started by: jackpotp
15 Replies
2. UNIX for Dummies Questions & Answers
Hi guys
I have a Caldera Openlinux 3.1.1 i'm new with this OS so please bear with me.
I have no idea about how to install my backup tape could any of you tell me how to do this.
I worked before with unix sco openserver 5.0.6 and i know that you can use scoadmin and then option (tape ).
... (1 Reply)
Discussion started by: josramon
1 Replies
3. Solaris
hello everybody...
i need some help ...
so... i need to do some backups from one solaris system and i dont know whitch is the best solution....to use tar or ufsdump...?
...and .... how can i restore files from tape if on the tape i have 2 sessions....how can i access second session....?
enough... (4 Replies)
Discussion started by: nich007
4 Replies
4. Solaris
How can I tell (from the command line) is compression is turned on for a tape drive?
I need to backup a system that is approx 150gb to a tape that has 110gb uncompress but 220gb available compressed.
Any ideas?
Also is it possible to turn compression on or off from the command line?
I am... (1 Reply)
Discussion started by: frustrated1
1 Replies
5. UNIX for Dummies Questions & Answers
Hi there: I'm new here
Can anyone help me:
I have DS15 Alpha server : Unix 5.1B
Now i need to connect a DLVT VS80 1U Rackmount Tape Drive unit.
What is the exact comman to mount the DLTape IV??
How do i make backuo @ copy file to the tape?
Thanx to all (0 Replies)
Discussion started by: ayzeayem
0 Replies
6. UNIX for Dummies Questions & Answers
Hi,
I performed backup on tape and I want to append more files to my previous backup on the same backup tape. But before I do that I need to know the backup file size of the first backup I performed so that I know the available size on the backup tape. Can someone help me what command I will use... (0 Replies)
Discussion started by: ayhanne
0 Replies
7. SCO
I am trying to make a full backup of my system using the cpio command. The Tape Unit is a SCSI DDS.
The process started fine but after about 30 minutes, it just stopped and showed the following message:
1755 Signal 31 - Core dumped
Any idea of what is causing this and how to fix it?
... (4 Replies)
Discussion started by: zionpc
4 Replies
8. UNIX for Dummies Questions & Answers
Hi All,
I would like some feedback / suggestion /recommendation about backup tape/disaster recovery for linux box as i'm new to linux.
We have linux box running as webserver which hosting website files.
I know that i have to backup all "website files". Is there any Linux system file i have... (2 Replies)
Discussion started by: c00kie88
2 Replies
9. AIX
Hi,
I am very new to AIX, i have a development and a production server with AIX 6.1. I am using following command to backup my system
/usr/bin/mksysb '-m' '-V' '-i' /dev/rmt0
You can what i have in my root volume group in the atached file and and you can also see the backup information of... (14 Replies)
Discussion started by: salmanucit
14 Replies
10. Solaris
Hi All!
Letīs say there are a few solaris servers connected to a NetApp storage device, but with no tape library or tape device attached to none of them. Assuming the O.S. is installed on the root disks, how to recover if the O.S. failed in one of the systems? Please share your ideas. (13 Replies)
Discussion started by: fretagi
13 Replies
LEARN ABOUT DEBIAN
discover.conf
discover.conf(5) File Formats Manual discover.conf(5)
NAME
discover.conf -- configuration file format for discover(1)
Description
Discover looks for configuration files in a configuration directory, containing a number of files. These define the system buses that
should be scanned by default, those that should never be scanned, and the URLs for hardware data files beyond the local copy provided with
the software.
The file format is XML; the DTD is provided with the Discover software, and can be used for informational or validation purposes.
Examples
Establishing default buses to scan
<?xml version="1.0"?>
<!DOCTYPE conffile SYSTEM "conffile.dtd">
<conffile>
<busscan scan="default">
<bus name="ata"/>
<bus name="pci"/>
<bus name="pcmcia"/>
<bus name="scsi"/>
<bus name="usb"/>
</busscan>
</conffile>
A more complex example
<?xml version="1.0"?>
<!DOCTYPE conffile SYSTEM "conffile.dtd">
<conffile>
<busscan scan="default">
<bus name="ata"/>
<bus name="pci"/>
<bus name="pcmcia"/>
<bus name="usb"/>
</busscan>
<!-- My ancient SCSI card locks up when probed -->
<busscan scan="never">
<bus name="scsi"/>
</busscan>
<data-sources>
<data-source url="http://www.example.com/discover/xfree86.xml"
label="Updated XFree86 hardware information">
</data-sources>
</conffile>
Authors
Josh Bressers, John R. Daily, and G. Branden Robinson developed the current implementation of Discover for Progeny Linux Systems.
The Linux implementation of the system-dependent interfaces is derived from detect, by MandrakeSoft SA.
See Also
discover(1)
discover.conf(5)