01-08-2004
Duplex Settings
Hi All
I've been having a lot of errors logged on the Cisco Catalyst (4000 series) which one of my Solaris servers is patched into. I have a feeling they are duplex related, but I'm a bit stuck as to how to confirm that.
How do I:
1. Check the duplex settings on my eri0 card?
2. Set the speed and duplex settings on my eri0 card (by command line, and also for every reboot)?
OS is Solaris 5.8, Sun Fire V880.
Thanks very much!
10 More Discussions You Might Find Interesting
1. IP Networking
Hi all,
What is the difference between half duplex and full duplex? What are the advantages and disadvantages of each mode, if any?
Thanks. (3 Replies)
Discussion started by: sihong
3 Replies
2. UNIX for Dummies Questions & Answers
Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub.
Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to.
... (4 Replies)
Discussion started by: merlin
4 Replies
3. UNIX for Dummies Questions & Answers
I am using digital Unix and lpd. I have HP 4200n LaserJet TCP printer, but when I use lpr command, it always print duplex.
I can turn off duplex feature at the panel of the printer, but then other Windows computer cannot print duplex. How can I set up /etc/printcap file so that it will be... (2 Replies)
Discussion started by: hiepng
2 Replies
4. Programming
what is meant by full duplex and half duplex?
b'coz in differences b\w hub and switch ,i heard lot this duplex word
so please help me (1 Reply)
Discussion started by: parvathy
1 Replies
5. HP-UX
Hi Folks,
I want the command to change the duplex settings of a HP-UX server.
Thanks in advance.
Sagar. (2 Replies)
Discussion started by: sag71155
2 Replies
6. Solaris
Evening,
I am attempting to change the speed and duplex settings on a single interface on a bge card on an m3000 SPARC server. Currently the settings are as follows:
bge0 link: up speed: 1000 Mbps duplex: full
bge1 link: up speed: 100 Mbps ... (13 Replies)
Discussion started by: brialt1
13 Replies
7. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
8. AIX
How to change Speed Duplex !
How to change Speed Duplex by command
chdev -P -l ent1 -a media_speed=1000_Full_Duplex
How to change Speed Duplex by Smitty .
smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
Discussion started by: ITHelper
0 Replies
9. UNIX for Advanced & Expert Users
I am able to use duplex printing with the -o duplex option. I am also printing landscape. It prints on the back of the page, however, I have to flip the page in order to see the other side right side up. Is there another option that will allow the duplex printing to print the right side up on front... (9 Replies)
Discussion started by: nickg
9 Replies
10. Shell Programming and Scripting
So I have a server I am trying to set up a script to send a Wall message notifying of my eth0 nic being set to 100 half duplex instead of 100 full duplex.
I know I am trying to read from /etc/sysconfig/network/ifcfg-eth0 to pull the parameters
STARTMODE=onboot
BOOTPROTO=static... (6 Replies)
Discussion started by: lutador72
6 Replies
TXP(4) BSD Kernel Interfaces Manual TXP(4)
NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device txp
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_txp_load="YES"
DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset.
Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload-
ing, tcp(4) segmentation, nor ipsec(4) acceleration.
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu-
tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of
attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.
The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are:
media autoselect
Attempt to autoselect the media type (default)
media 100baseTX mediaopt full-duplex
Use 100baseTX, full duplex
media 100baseTX [mediaopt half-duplex]
Use 100baseTX, half duplex
media 10baseT mediaopt full-duplex
Use 10baseT, full duplex
media 10baseT [mediaopt half-duplex]
Use 10baseT, half duplex
HARDWARE
The txp driver supports the following cards:
o 3Com 3CR990-TX-95
o 3Com 3CR990-TX-97
o 3Com 3cR990B-TXM
o 3Com 3CR990SVR95
o 3Com 3CR990SVR97
o 3Com 3cR990B-SRV
SEE ALSO
altq(4), arp(4), inet(4), intro(4), ip(4), miibus(4), tcp(4), udp(4), vlan(4), ifconfig(8)
HISTORY
The txp driver first appeared in OpenBSD 2.9.
BSD March 12, 2009 BSD