01-07-2004
yes, /dev/rmt0 is there, and if i run
# lsdev -Cc tape
rmt0 Available 40-60-00-0,0 SCSI 8mm Tape Drive
this leads me to believe it is available
what command is this?
mt -f /dev/rmt/0 status
specifically the mt command?
8 More Discussions You Might Find Interesting
1. AIX
Currently I have a Dell Ultrium LTO 2 Tape Drive. I am going to have a IBM AIX server. Just wonder if it is possibe to connect this tape drive to the aix server? I have Brightstor Arcserver installed on another win 2003 server. Is it possible to install the arcserve agent on the aix and use the... (1 Reply)
Discussion started by: ming413
1 Replies
2. AIX
I've just landed in a situation where an old IBM RS/6000 7025 F40 running AIX 4.2.1 has had it's tape drive fail. The tape drive in question is an HP C1533A 4mm 4GB/8GB DAT drive. It repeatedly gets write failures, and my trusty techique of whacking the cleaning tape in hasn't worked. Unfortunately... (2 Replies)
Discussion started by: phaedrus
2 Replies
3. AIX
Hi,
Help required!
How to mount internal tape drive of sun machine in AIX 5.3 (0 Replies)
Discussion started by: ashwin.krishna
0 Replies
4. AIX
Hi,
I have recently purchase a SUN Storage Tek desktop LTO 4 HH tape drive and connected to a IBM AIX 5.1 server.
The server can detect the tape device.
Can someone please advice urgently.
Thanks (4 Replies)
Discussion started by: Caully
4 Replies
5. AIX
I am trying to use this command to eject the tape
mt -f /dev/rmt/0 unload
but it gives me error
mt -f /dev/rmt/0 unload
mt: 0511-575 unload is not a recognized subcommand.
Usage: mt Subcommand
Valid subcommands are:
weof
eof
fsf
bsf
... (5 Replies)
Discussion started by: filosophizer
5 Replies
6. AIX
Hi,
The problem I have is I want to restore my AIX machine. I have created a mksysb tape from my tape drive rmt0 and I changed the bootlist using this command "bootlist -m normal rmt0 hdisk0".
However, when I display the bootlist "bootlist -om normal", it shows '-' hdisk0. I googled and... (2 Replies)
Discussion started by: AixNoob87
2 Replies
7. AIX
Hi
I need to make some restore tapes for our old AIX systems
I have purchased some DDS2 tapes and cleaning tapes
The tape drive is rmt0
what commands can I enter to run the cleaning tape through the drive
and are the any commands I can enter to test these drives
prior to using... (2 Replies)
Discussion started by: madmacher
2 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
TM(4) Kernel Interfaces Manual TM(4)
NAME
tm - TM-11/TU-10 magtape interface
DESCRIPTION
The files mt0, ..., mt7 refer to the DEC TU10/TM11 magtape. When closed it can be rewound or not, see below. If it was open for writing,
two end-of-files are written. If the tape is not to be rewound it is positioned with the head between the two tapemarks.
If the 0200 bit is on in the minor device number the tape is not rewound when closed.
A standard tape consists of a series of 512 byte records terminated by an end-of-file. To the extent possible, the system makes it possi-
ble, if inefficient, to treat the tape like any other file. Seeks have their usual meaning and it is possible to read or write a byte at a
time. Writing in very small units is inadvisable, however, because it tends to create monstrous record gaps.
The mt files discussed above are useful when it is desired to access the tape in a way compatible with ordinary files. When foreign tapes
are to be dealt with, and especially when long records are to be read or written, the `raw' interface is appropriate. The associated files
are named rmt0, ..., rmt7. Each read or write call reads or writes the next record on the tape. In the write case the record has the same
length as the buffer given. During a read, the record size is passed back as the number of bytes read, provided it is no greater than the
buffer size; if the record is long, an error is indicated. In raw tape I/O, the buffer must begin on a word boundary and the count must be
even. Seeks are ignored. A zero byte count is returned when a tape mark is read, but another read will fetch the first record of the new
tape file.
FILES
/dev/mt?, /dev/rmt?
SEE ALSO
tp(1)
BUGS
If any non-data error is encountered, it refuses to do anything more until closed. In raw I/O, there should be a way to perform forward
and backward record and file spacing and to write an EOF mark.
TM(4)