07-25-2001
Configuring a Server
In order to change the settings of your servers, the simplest solution is to run a "sys-unconfig" as root.
At the "OK>" Prompt, make sure that you type "boot" in order to continue the process unless it will seem to hang.
After this point, the screen typically becomes white, with black lettering. Make the necessary entries and changes according to your new environment settings (i.e. time zone, i.p. address, netmask, root password,etc.)
The system will automatically reboot. When the login screen is reached, do NOT enter as any user but, for safety, hold down the "stop" key with the letter "a" and, when the "OK>" is shown, type "reboot"
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
My OS is sun solaris7,(sun sparc),i want connect inernet and my computer in my company intranet.After i configure proxy server,i still can't conncet internet.I guess whether the DNS is configured correctly.
who can help me???Thank you very much!!! (6 Replies)
Discussion started by: q30
6 Replies
2. UNIX for Dummies Questions & Answers
my compiler won' t let me configure. This is what occurs when I type ./configure
Alex@BADPERSON /postgresql-7.2.1
$ ./configure
loading cache ./config.cache
checking host system type... i686-pc-cygwin
checking which template to use... win
checking whether to build with locale support... no... (3 Replies)
Discussion started by: achink125
3 Replies
3. UNIX for Advanced & Expert Users
Hi:
I need some information about how to configure a dktab archive to make mirroring with ide disk.
I have to know the necesary steps to make that.
Thanks. (2 Replies)
Discussion started by: dvl
2 Replies
4. HP-UX
Hi
I'm new about UNIX, but I've to use a HP9000 with HP-UX 10.20 workstation. I'm trying to configure the network, I've configured the file /etc/rc.conf.d/netconf with my IP address and the right gateway, so the HP9000 is on the net, I've tried a ping. But now I've a problem I can't start hte CDE,... (4 Replies)
Discussion started by: gofmass
4 Replies
5. Programming
I am using emacs to write c++ code. How to configure it to let the system highlight C++ keywords, variables, etc; and let it automatically indent, just like a common C++ IDE does?
Any suggestions? Thanks! (1 Reply)
Discussion started by: meili100
1 Replies
6. Linux
Hi,
I've installed wireless card and I didn't receive any error in the installation process.
Now I want to use it but I can't make internet to work.
if I check my card with iwconfig I get the following message
wlan0 IEEE 802.11g ESSID:"Alice-34376718"
Mode:Managed ... (2 Replies)
Discussion started by: aneuryzma
2 Replies
7. Solaris
Hello Group,
Could you please help me with the procedure to configure a virtual ip (second ip) under the same interface in Solaris 11.
Thanks in advance ! (2 Replies)
Discussion started by: csierra
2 Replies
8. Red Hat
Hi..i need to install package (*.rpm) on RHEL 6.2 . I have those patches available in RPM disc. When i try using below command
rpm -ivh <package name>
it give me following error
no key
warning:user mockbuild does not exist - using root
warning:group mockbuild does not exist - using root... (3 Replies)
Discussion started by: deljatt
3 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I'm trying to install sudo on Solaris 10. I have added the package. The notes said to use "./configure", "./make" and "./make install" to complete the installation. However, none of the commands are found.
Can you please tell me how to enable it or how else can i install the package.
... (4 Replies)
Discussion started by: Scarlet
4 Replies
10. UNIX for Dummies Questions & Answers
hello,
I'm trying install apache http server version 2.2.22.
I downloaded the file httpd-2.2.22.tar.bz2.
I unzipped this file..
When I type "./configure", the following error occurs:
# ./configure --prefix=/opt/work/apache2.2.22
checking for chosen layout... Apache
checking for... (1 Reply)
Discussion started by: Adriano Schmidt
1 Replies
LEARN ABOUT XFREE86
sulogin
sulogin(1M) System Administration Commands sulogin(1M)
NAME
sulogin - access single-user mode
SYNOPSIS
sulogin
DESCRIPTION
The sulogin utility is automatically invoked by init when the system is first started. It prompts the user to type the root password to
enter system maintenance mode (single-user mode) or to type EOF (typically <CTRL-D>) for normal startup (multi-user mode). The user should
never directly invoke sulogin.
The sulogin utility can prompt the user to enter the root password on a variable number of serial console devices, in addition to the tra-
ditional console device. See consadm(1M) and msglog(7D) for a description of how to configure a serial device to display the single-user
login prompt.
FILES
/etc/default/sulogin Default value can be set for the following flag:
PASSREQ Determines if login requires a password. Default is PASSREQ=YES.
/etc/default/login Default value can be set for the following flag:
SLEEPTIME If present, sets the number of seconds to wait before login failure is printed to the screen and
another login attempt is allowed. Default is 4 seconds. Minimum is 0 seconds. Maximum is 5 seconds.
Both su(1M) and login(1) are affected by the value of SLEEPTIME.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsr |
+-----------------------------+-----------------------------+
SEE ALSO
login(1), consadm(1M), init(1M), su(1M), attributes(5), msglog(7D)
SunOS 5.10 25 Sep 2002 sulogin(1M)