11-20-2003
You can run sshd in debug mode:
-d Debugging mode (multiple -d means more debugging)
Maybe it is because it's on SCO
Cheers,
Keith
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies
3. SCO
Dear members
when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config.
i tried MP4, EFS 5.64,5.70A but not solved the problem.. (0 Replies)
Discussion started by: M_farooqui
0 Replies
4. AIX
I just installed SSH on an AIX machine:
> lslpp -l openssh.base.server
Fileset Level State Description
----------------------------------------------------------------------------
Path: /usr/lib/objrepos
openssh.base.server 4.1.0.5301 COMMITTED Open... (1 Reply)
Discussion started by: outtacontrol
1 Replies
5. SCO
Hello,
My System configuration is as:
IDE Hrad Disk = 80GB
RAM = 512MB
While doing installation of SCO Open Server 5.0.7, I got stuck at second phase (i.e. IQM). During this phase, I selected for "Fresh" installtion and after that I go for "Customizing Partitions and FileSystems". But it... (0 Replies)
Discussion started by: ghimanshu
0 Replies
6. UNIX for Advanced & Expert Users
Hello,
My System configuration is as:
IDE Hrad Disk = 80GB
RAM = 512MB
While doing installation of SCO Open Server 5.0.7, I got stuck at second phase (i.e. IQM). During this phase, I selected for "Fresh" installtion and after that go for "Customizing Partitions and FileSystems". But it... (3 Replies)
Discussion started by: ghimanshu
3 Replies
7. SCO
Hi there
I have compiled a binary of stunnel for SCO Openserver 5.0.7
At the moment the binary is in /u/testroom/sbin/stunnel
as root I cd to /u/testroom/sbin and start the stunnel daemon up with ./stunnel
The stunnel log shows when users successfully connect or disconnect, so... (1 Reply)
Discussion started by: The_Librarian
1 Replies
8. Solaris
We have a number of system running the same patch level, OS version and sshd version. The systems also have the same sshd config and syslog.conf entries , however one of the systems keeps logging the following message everytime someone logs in:
Nov 16 09:36:02 server389 sshd: Failed none for... (3 Replies)
Discussion started by: Mr_Webster
3 Replies
9. SCO
Hi all,
I have a customer whose sco unix server wasnt power off correctly and when booting it up I noticed that the boot up takes a while to finish the " Starting TCP services: snmpd routed lpd". after that the server is ready for login, but you cannot ping anything from the server (apart from... (2 Replies)
Discussion started by: CharlL
2 Replies
10. SCO
Hi, I am a new Unix Guru with very little experience but have the task of P2Ving an old HP Proliant ML370 G5 server to VMware ESX 4.1 or ESXi 5.5.
System seems to boots fine but when trying to remove HP software, configure TCP/IP or a driver, I am receiving:
--------
... (7 Replies)
Discussion started by: dj_Italian
7 Replies
LEARN ABOUT PHP
sftp-server
sftp-server(1M) System Administration Commands sftp-server(1M)
NAME
sftp-server - SFTP server subsystem
SYNOPSIS
/usr/lib/ssh/sftp-server
DESCRIPTION
sftp-server implements the server side of the SSH File Transfer Protocol as defined in the IETF draft-ietf-secsh-filexfer.
sftp-server is a subsystem for sshd(1M) and must not be run directly. There are no options or config settings.
To enable the sftp-server subsystem for sshd add the following to /etc/ssh/sshd_config:
Subsystem sftp /usr/lib/ssh/sftp-server
See sshd_config(4) for a description of the format and contents of that file.
There is no relationship between the protocol used by sftp-server and the FTP protocol (RFC 959) provided by in.ftpd.
EXIT STATUS
The following exit values are returned:
0 Successful completion.
>0 An error occurred.
FILES
/usr/lib/sftp-server
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWsshdu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO
sftp(1), ssh(1), ssh-add(1), ssh-keygen(1), sshd(1M), sshd_config(4), attributes(5)
To view license terms, attribution, and copyright for OpenSSH, the default path is /var/sadm/pkg/SUNWsshdr/install/copyright. If the
Solaris operating environment has been installed anywhere other than the default, modify the given path to access the file at the installed
location.
AUTHOR
Markus Friedl
SunOS 5.10 30 Jul 2003 sftp-server(1M)