11-07-2003
danke to you both...
this goes in curious infomation file.
8 More Discussions You Might Find Interesting
1. AIX
I am trying to find a command to return the "link" speed of the networks installed on AIX.
ifconfig - gives me where the link is up and the duplex setting. I need to determine for example if the ethernet connection is 10, 100, 1000 Mbs or what the current speed is based on the network media... (3 Replies)
Discussion started by: karlgo
3 Replies
2. UNIX for Dummies Questions & Answers
hai this is nagesh
when i was doing practical , i find some dought.
iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me (4 Replies)
Discussion started by: nag.mi2000
4 Replies
3. Solaris
Hi Friends,
I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance. (1 Reply)
Discussion started by: kurva
1 Replies
4. Solaris
I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
Discussion started by: StarSol
4 Replies
5. Red Hat
Hi guys,
Suppose you have a server with two ethernet cards (1GB each) and each cards are connecting to two different switches cisco 3750. My question is:
How can I setup my server's network interfaces to increase the throughput up to 2GB? is it possible? If not, do you know another way to up... (3 Replies)
Discussion started by: iga3725
3 Replies
6. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
7. UNIX for Dummies Questions & Answers
Hi,
I went to a computer store and the salesman sold me a SATA cable and told me that all SATA cables are the same. Another salesman at a different store told me a cable rated for SATA 2, which I bought, MIGHT work as well as one rate for SATA 3 but it is not guaranteed. I decided to run a... (3 Replies)
Discussion started by: mojoman
3 Replies
8. AIX
Hello.
I have a server RS/6000 with AIX 4.2. The server have a network card with 10/100mbps speed, but for some reason, the ethernet only runs at 10Mbps, it doesn,t matter if I put the net cable on a 100Mbps switch, it keeps running at 10Mbps speed....
I know how to view/change ethernet speed... (1 Reply)
Discussion started by: little_ball
1 Replies
xrestop(1) General Commands Manual xrestop(1)
NAME
xrestop - monitor server resources used by X11 clients
SYNOPSIS
xrestop -help
xrestop [ -display display ] [ --batch ] [ --delay-time seconds ]
DESCRIPTION
Xrestop uses the X-Resource extension to provide 'top'-like statistics of each connected X11 client's server-side resource usage. It is
intended as a developer tool to aid more efficient server resource usage and debug server-side resource leakage.
OPTIONS
--help Show usage.
--display, -d <display>
Specify X11 display to monitor.
--delay-time, -dt <seconds>
Time in seconds between taking samples. Default is 2 seconds.
--batch, -b
Run in batch mode. Slightly more detailed infomation is streamed to stdout rather than the usual curses interface. This mode is
intended for debugging a single client with something like
xrestop -b | grep -A 14 appname
--max-samples, -m <count>
Specify number of times to gather and display results. Default is continuous, which can be set with 0 (zero).
SEE ALSO
X(7), top(1).
BUGS
The X-Resource extension is very new and may not be 100% accurate.
AUTHOR
xrestop was written by Matthew Allum <mallum@handhelds.org>.
xrestop(1)