determining ethernet port speed in solaris Post: 42944

8 More Discussions You Might Find Interesting

1. AIX

AIX - Determining link speed

I am trying to find a command to return the "link" speed of the networks installed on AIX. ifconfig - gives me where the link is up and the duplex setting. I need to determine for example if the ethernet connection is 10, 100, 1000 Mbs or what the current speed is based on the network media...

2. UNIX for Dummies Questions & Answers

how can i see ethernet card speed in solars

hai this is nagesh when i was doing practical , i find some dought. iam using solaris 9. how can i see the ethernet card speed , wheather it is halfduplex or full duplex.any body please help me

3. Solaris

Reg. Ethernet port

Hi Friends, I am using intel system installed solaris 10, when i check ifconfig -a it doesn't show any thing eg-for HP servers hme0, for sun servers-iprb0. for me it doesn't show any thing, and tell me what files to be modified. Thanks in Advance.

4. Solaris

Ethernet Port Name

I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ?

5. Red Hat

Duplicating ethernet speed

Hi guys, Suppose you have a server with two ethernet cards (1GB each) and each cards are connecting to two different switches cisco 3750. My question is: How can I setup my server's network interfaces to increase the throughput up to 2GB? is it possible? If not, do you know another way to up...

6. UNIX for Advanced & Expert Users

Determine the ethernet (NIC) card speed.

Hi, Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux. I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS....

7. UNIX for Dummies Questions & Answers

Determining Disk Speed

Hi, I went to a computer store and the salesman sold me a SATA cable and told me that all SATA cables are the same. Another salesman at a different store told me a cable rated for SATA 2, which I bought, MIGHT work as well as one rate for SATA 3 but it is not guaranteed. I decided to run a...

8. AIX

AIX 4.2 increase ethernet speed

Hello. I have a server RS/6000 with AIX 4.2. The server have a network card with 10/100mbps speed, but for some reason, the ethernet only runs at 10Mbps, it doesn,t matter if I put the net cable on a 100Mbps switch, it keeps running at 10Mbps speed.... I know how to view/change ethernet speed...

LEARN ABOUT DEBIAN

myson-diag

MYSON-DIAG(8)						      System Manager's Manual						     MYSON-DIAG(8)

NAME

       myson-diag - EEPROM setup and diagnostic program for ethernet cards based on the Myson MTD803 chip.

SYNOPSIS

       myson-diag [options]

DESCRIPTION

       myson-diag is a program that you can use to diagnose problems with ethernet cards based on the Myson MTD803 chip.

OPTIONS

       These  programs	follow	the  usual  GNU  command  line	syntax, with long options starting with two dashes (`-').  A summary of options is
       included below.

       -h, --help
	      Show summary of options.

       -V, --version
	      Show version of program.

       -v, --verbose
	      Verbose mode.

       -q, --quiet
	      Be very unverbose.

       -# <cardnum>
	      Use card number <cardnum>.

       -a, --show_all_registers
	      Print all registers.

       -e, --show-eeprom
	      Dump EEPROM contents to stdout.

       -E, --emergency-rewrite
	      Re-write a corrupted EEPROM.

       -p, --port-base <port>
	      Specify port to use.

       -A, --Advertise <mediaype>
	      Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.

       -F, --new-interface <interface>
	      Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX,  100baseT4,	100baseFx,
	      100baseFx-FDX, MII and Autosense.

       -H, --new-hwaddress <address>
	      Set card to a new hardware address.

       -m, --show-mii
	      Dump MII management registers.

       -R, --reset
	      Reset the transceiver.

       -T, --test
	      Do register and SRAM test.

       -w, --write-EEPROM <values>
	      Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!

       -f, --force-detection
	      Try to identify the card, even if it is active.

       -t, --chip-type <card>
	      Explicitly set the chip. To get all valid numbers, run myson-diag with the options '-t -1'.

SEE ALSO

       mii-diag(8)

AUTHOR

       myson-diag  was	written  and  is  still  maintained  by Donald Becker <becker@scyld.com>.  This manual page was written by Alain Schroeder
       <alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).

								 February 18, 2002						     MYSON-DIAG(8)