Parallel Tape Drive on Ultra 5? Post: 42435

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

hard drive in Sun Ultra 10

What are the options on upgrading disk space in an Ultra 10 workstation? Sun states they are EIDE drives, are they standard or Sun specific? Thanks

2. Filesystems, Disks and Memory

Disk drive and Ultra 10

I need more space on my Ultra 10, and was thinking of a pair of 60 or 80 GB 7200 rpm ATA/100 drives mirrored with DiskSuite. Will afterarket IDE drives work in the Sun box? Are there any issues?

3. Filesystems, Disks and Memory

Tape Drive Connected to a Sun Ultra 10/Solaris 2.7

I have a Sun Ultra 10/Solaris 2.7 with a differential SCSI card connected to a Supter DLt1 Tape Drive. When I boot the machine, and I do a probe-scsi-all in the very beginning of the boot process. It shows up correctly. If I wait for the boot process to proceed and then I do a probe-scsi-all, I get...

4. Programming

parallel port proramming for sun ultra

Hi I'm trying to look for information about reading/writing to the parallel port of a Sun Ultra 5 running Solaris 8. I'd just like to see some basic programs written in C, nothing fancy, just reading and wrting to the port, getting the port address etc. toggling the lines. I've tried searching...

5. Solaris

Problem with SCSI DAT drive on Ultra 10

I will be honest I am quite new to UNIX and Solaris so this may be a simple thing. I have just purchased a Sun (rebranded HP obviously) DAT DDS3 SCSI tape drive for my Sun Ultra 10 running Solaris 10. I have previously fitted a SCSI card to the box which has configured ok and can be seen from...

6. HP-UX

Mounting an external parallel hard drive

Can anyone please walk me through how to mount an external parallel (or scsi) hard drive in visualize C3000 machine? I also would like to mount "/var/sallie" directory in that external drive. My "/var/sallie" directory is running out of space so I would like to mount an external hard drive so that...

7. Solaris

Connect an External SCSI Hard Drive to Ultra 80

Guys, I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem. I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80. I connected it powered it up and at OK prompt did : boot -r system comes up and complains about not...

8. Solaris

Sun Ultra 2 Hard Drive Replacement

Hi all...I have an old Sun Ultra 2 running SunOS 5.7 (I know old). These machines have 2 hard drives and one of my drives fried. I bought some replacement drives and wanted to a simple "dd" command from my one good drive to copy all to the new replacement drive. The new drives however give me a...

LEARN ABOUT DEBIAN

trm

TRM(4)							   BSD Kernel Interfaces Manual 						    TRM(4)

NAME

     trm -- Tekram TRM-S1040 ASIC based PCI SCSI host adapter driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device scbus
	   device trm

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   trm_load="YES"

DESCRIPTION

     The trm driver supports PCI SCSI host adapters based on the Tekram TRM-S1040 SCSI ASIC.

HARDWARE

     SCSI controllers supported by the trm driver include:

     o	 Tekram DC-315 PCI Ultra SCSI adapter without BIOS and internal SCSI connector
     o	 Tekram DC-315U PCI Ultra SCSI adapter without BIOS
     o	 Tekram DC-395F PCI Ultra-Wide SCSI adapter with flash BIOS and 68-pin external SCSI connector
     o	 Tekram DC-395U PCI Ultra SCSI adapter with flash BIOS
     o	 Tekram DC-395UW PCI Ultra-Wide SCSI adapter with flash BIOS
     o	 Tekram DC-395U2W PCI Ultra2-Wide SCSI adapter with flash BIOS

     For the Tekram DC-310/U and DC-390F/U/UW/U2B/U2W/U3W PCI SCSI host adapters, use the sym(4) driver.

SEE ALSO

     cd(4), ch(4), da(4), intro(4), sa(4), scsi(4), sym(4)

     http://www.tekram.com/

AUTHORS

     The trm driver was originally written for FreeBSD 3.0/i386 by Erich Chen of Tekram Technology, and ported to FreeBSD 5.0 by Olivier Houchard
     <cognet@FreeBSD.org>.

BSD
								 December 8, 2002							       BSD