10-21-2003
Ok, I just read that page. Those docs are not great. ce is a card that you could get. You are using an eri card instead. They did also setup a ce0. Did you setup a eri0? If so, get rid of that and try it again.
If it's not that, then I don't know.
10 More Discussions You Might Find Interesting
1. IP Networking
Hi all,
so server: FreeBSD 7.0 release,
interfaces on it DLINK DGE-528T with support of vlans :))
so first interface looks to LAN second to ISP.
I created vlan1 with id 1 and gave to it ip address and plug it in
tagged port of swith for vlan 1. so client from vlan1 reaches the server.
it... (2 Replies)
Discussion started by: samar
2 Replies
2. Solaris
I 've a T5220 running solaris 10u6 with Ldoms 1.1. following is o/p of my dladm
e1000g0 type: non-vlan mtu: 1500 device: e1000g0
e1000g1 type: non-vlan mtu: 1500 device: e1000g1
e1000g531001 type: vlan 531 mtu: 1500 device: e1000g1
e1000g2 ... (0 Replies)
Discussion started by: fugitive
0 Replies
3. AIX
I have a aix 5.3, two network adapter, configure as a etherchannel, how can I know the vlan id by command? (4 Replies)
Discussion started by: rainbow_bean
4 Replies
4. Programming
Hi all
My application is a monitoring application that monitors the incoming udp packet when ever required. When ever a particular source ip and port and dest ip and port is provided the filter will be framed based them. For eg,
char filterExpr;
filterExpr = "udp and src host 192.168.16.100... (0 Replies)
Discussion started by: anusha_pixel
0 Replies
5. IP Networking
Hello. I want to Communicate 2 VLAN with router like this solution:
http://8pic.ir/images/83m0ouih8mmm9s1sfl56.jpg
For this purpose I'm configuring 2 Linux system as a switch and connect 4 host to them. Then a router is added to scenario.
The configuration of the switches is:
On DUT1(Linux):... (1 Reply)
Discussion started by: zsn
1 Replies
6. Solaris
Hi,
Is it possible to VLAN tag with a ce interface on Solaris 9? Link speed is gb.
ce:0:ce0:link_speed 1000
I have a ce0 interface I would need to have access to another VLAN as well as the one it's currently on.
What commands would I need to run?
Thanks.;) (2 Replies)
Discussion started by: sparcman
2 Replies
7. Red Hat
We have two hosts in same vlan with same route rules.
One of them is not able to connect to an outside IP while in another I get "failed: Connection timed out" while testing the connectivity through netcat.
I have tried mtr /traceroute and it gives me the same results.
Is there a netcat... (1 Reply)
Discussion started by: jacki
1 Replies
8. Solaris
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
Discussion started by: Shirishlnx
0 Replies
9. AIX
Hi Guys,
Our lpars is currently running on 2 different vlans (20, 30). Now we have a requirement that vlan 30 needs to be change to vlan 31 at the same subnet. I'm not sure on what is the best approach for this or what change is involve on the AIX side.
This is our setup.
Network switch -... (5 Replies)
Discussion started by: kaelu26
5 Replies
10. Solaris
Hi Folks,
I am currently moving systems to a new environment, with some changes to the network requirements on the systems.
One of these changes is moving from just standard IPMP to using IPMP on top of a VLAN, I have used VLAN tagging befor without issue - however not with IPMP.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
LEARN ABOUT CENTOS
opensc-tool
OPENSC-TOOL(1) OpenSC Tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--atr, -a
Print the Answer To Reset (ATR) of the card. Output is in hex byte format
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--info, -i
Print information about OpenSC, such as version and enabled components.
--list-drivers, -D
List all installed card drivers.
--list-files, -f
Recursively list all files stored on card.
--list-readers, -l
List all configured readers.
--name, -n
Print the name of the inserted card (driver).
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....
--serial
Print the card serial number (normally the ICCSN). Output is in hex byte format
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
--wait, -w
Wait for a card to be inserted.
SEE ALSO
opensc-explorer(1)
opensc 06/17/2014 OPENSC-TOOL(1)