Sun Ultra30, Gentoo 1.4.3.10p1 Post: 41443

Sponsored Content

UNIX Standards and Benchmarks UNIX & LINUX Benchmarks (Version 3.11) Linux Benchmarks Sun Ultra30, Gentoo 1.4.3.10p1 Post 41443 by tnorth on Monday 6th of October 2003 12:14:31 PM

10-06-2003

Registered User

Sun Ultra30, Gentoo 1.4.3.10p1

Notes:

Code:

CPU/Speed: UltraSparcII 296Mhz
Ram:512M
Motherboard:
Bus:
Cache:
Controller:
Disk: SEAGATE Model: ST34371W SUN4.2G
Load:
Kernel:
Kernel ELF?:
pgms:

Results:


  BYTE UNIX Benchmarks (Version 3.11)
  System -- Linux box  2.4.21-sparc-r1 #1 Wed Oct 1 12:32:52 EDT 2003 sparc64 sun4u TI UltraSparc II (BlackBird) GNU/Linux
  Start Benchmark Run: Mon Oct  6 10:35:11 EDT 2003
   1 interactive users.
Dhrystone 2 without register variables   576386.0 lps   (10 secs, 6 samples)
Dhrystone 2 using register variables     579571.7 lps   (10 secs, 6 samples)
Arithmetic Test (type = arithoh)         2328097.3 lps   (10 secs, 6 samples)
Arithmetic Test (type = register)         31883.2 lps   (10 secs, 6 samples)
Arithmetic Test (type = short)            30893.1 lps   (10 secs, 6 samples)
Arithmetic Test (type = int)              31726.1 lps   (10 secs, 6 samples)
Arithmetic Test (type = long)             31917.1 lps   (10 secs, 6 samples)
Arithmetic Test (type = float)            91624.5 lps   (10 secs, 6 samples)
Arithmetic Test (type = double)           71655.4 lps   (10 secs, 6 samples)
System Call Overhead Test                122951.4 lps   (10 secs, 6 samples)
Pipe Throughput Test                     103068.5 lps   (10 secs, 6 samples)
Pipe-based Context Switching Test         41634.4 lps   (10 secs, 6 samples)
Process Creation Test                      1922.9 lps   (10 secs, 6 samples)
Execl Throughput Test                       537.8 lps   (9 secs, 6 samples)
File Read  (10 seconds)                  480789.0 KBps  (10 secs, 6 samples)
File Write (10 seconds)                  122483.0 KBps  (10 secs, 6 samples)
File Copy  (10 seconds)                   35198.0 KBps  (10 secs, 6 samples)
File Read  (30 seconds)                  483378.0 KBps  (30 secs, 6 samples)
File Write (30 seconds)                  113817.0 KBps  (30 secs, 6 samples)
File Copy  (30 seconds)                   17388.0 KBps  (30 secs, 6 samples)
C Compiler Test                             183.3 lpm   (60 secs, 3 samples)
Shell scripts (1 concurrent)                958.2 lpm   (60 secs, 3 samples)
Shell scripts (2 concurrent)                507.8 lpm   (60 secs, 3 samples)
Shell scripts (4 concurrent)                261.7 lpm   (60 secs, 3 samples)
Shell scripts (8 concurrent)                132.0 lpm   (60 secs, 3 samples)
Dc: sqrt(2) to 99 decimal places          25150.8 lpm   (60 secs, 6 samples)
Recursion Test--Tower of Hanoi            10871.8 lps   (10 secs, 6 samples)


                     INDEX VALUES
TEST                                        BASELINE     RESULT      INDEX

Arithmetic Test (type = double)               2541.7    71655.4       28.2
Dhrystone 2 without register variables       22366.3   576386.0       25.8
Execl Throughput Test                           16.5      537.8       32.6
File Copy  (30 seconds)                        179.0    17388.0       97.1
Pipe-based Context Switching Test             1318.5    41634.4       31.6
Shell scripts (8 concurrent)                     4.0      132.0       33.0
                                                                 =========
     SUM of  6 items                                                 248.3
     AVERAGE                                                          41.4

tnorth

View Public Profile for tnorth

Find all posts by tnorth

4 More Discussions You Might Find Interesting

1. Linux Benchmarks

AMD 1.2 Gentoo 1.4.3.8p1

Notes: CPU/Speed: 1195.993 Ram: 503 Megabytes Motherboard: biostart m7vkb Bus: Cache:256 KB Controller:VT82C586A Disk:Maxtor 93073U6 Load: Kernel:2.4.20-xfs-r3 Kernel ELF?: yes pgms: Results: BYTE UNIX Benchmarks (Version 3.11) System -- Linux box 2.4.20-xfs-r3 #1...

2. Gentoo

Gentoo problem, X is not working

I got Gentoo installed with only a few minor problems, but those are the worse right? :p Anyway, I can boot into a terminal and could could fine into TWM (yuck). So I emerged XFCE4 by doing this: use="-gnome -kde" emerge xfce I then inserted this into ~./xinitrc : ...

3. Gentoo

Gentoo and Qmail

Hello all, I want to create a qmail to just forward messages to a valid smtp over the internet, so I can use mutt to send messages as well as recieving them. Is there an easy way of doing this? My SMTP server requires authentication. Thanks a lot.

4. UNIX for Advanced & Expert Users

Installing oracle on Gentoo

Hello! I'm using Linux Gentoo 2.6.22-gentoo-r9. Before I used Red Had I had no issues with the installation. But I don't like Red Hat and trying to install Oracle on Gentoo. See following: rpm --nodeps -vv -i oracle-xe-10.2.0.1-1.0.i386.rpm ... You must run '/etc/init.d/oracle-xe...

LEARN ABOUT DEBIAN

lscpu

LSCPU(1)							   User Commands							  LSCPU(1)

NAME

       lscpu - display information on CPU architecture

SYNOPSIS

       lscpu [-hpx] [-s directory]

DESCRIPTION

       lscpu gathers CPU architecture information like number of CPUs, threads, cores, sockets, NUMA nodes, information about CPU caches, CPU fam-
       ily, model, bogoMIPS, byte order and stepping from sysfs and /proc/cpuinfo, and prints it in a human-readable  format.	It  supports  both
       online  and  offline  CPUs.  It can also print out in a parsable format, including how different caches are shared by different CPUs, which
       can be fed to other programs.

OPTIONS

       -h, --help
	      Print a help message.

       -p, --parse [=list]
	      Print out in parsable instead of human-readable format.

	      If the list argument is not given then the default backwardly compatible output is printed.  The backwardly compatible  format  uses
	      two commas to separate CPU cache columns. If no CPU caches are identified, then the cache columns are not printed at all.

	      The  list  argument is comma delimited list of the columns. Currently supported are CPU, Core, Node, Socket, Book and Cache columns.
	      If the list argument is given then always all requested columns are printed in the defined order. The Cache columns are separated by
	      ':'.

	      Note  that  the optional list argument cannot be separated from the option by a space, the correct form is for example '-p=cpu,node'
	      or '--parse=cpu,node'.

       -s, --sysroot directory
	      Use the specified directory as system root.  This allows you to inspect a snapshot from a different system.

       -x, --hex
	      Use hexadecimal masks for CPU sets (e.g. 0x3).  The default is to print the sets in list format (e.g. 0,1).

BUGS

       The basic overview about CPU family, model, etc. is always based on the first CPU only.

       Sometimes in Xen Dom0 the kernel reports wrong data.

AUTHOR

       Cai Qian <qcai@redhat.com>
       Karel Zak <kzak@redhat.com>

AVAILABILITY

       The lscpu command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.

util-linux							   February 2011							  LSCPU(1)