Sponsored Content
Full Discussion: Sun Ultra 30 Solaris 8
UNIX Standards and Benchmarks UNIX & LINUX Benchmarks (Version 3.11) UNIX Benchmarks Sun Ultra 30 Solaris 8 Post 41440 by tnorth on Monday 6th of October 2003 12:10:07 PM
Old 10-06-2003
Notes:

CPU/Speed: UltraSparcII 296Mhz
Ram:512M
Motherboard:
Bus:
Cache:
Controller:
Disk: SEAGATE Model: ST34371W SUN4.2G
Load:
Kernel:
Kernel ELF?:
pgms:
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Sun Ultra sparc 60

Hello everybody!! I need your help again. I am using Sun Ultra sparc 60 machine.Follwing are the types of files getting generated in /var/tmp. "windu_sm_o aaaa,baaa,caaa,daaa" etc. I am not able to locate which application is generating these files. Can I straightway delete these files ? or... (1 Reply)
Discussion started by: vikasdeshmukh
1 Replies

2. Filesystems, Disks and Memory

Tape Drive Connected to a Sun Ultra 10/Solaris 2.7

I have a Sun Ultra 10/Solaris 2.7 with a differential SCSI card connected to a Supter DLt1 Tape Drive. When I boot the machine, and I do a probe-scsi-all in the very beginning of the boot process. It shows up correctly. If I wait for the boot process to proceed and then I do a probe-scsi-all, I get... (1 Reply)
Discussion started by: brv
1 Replies

3. UNIX Benchmarks

Sun Ultra 2 Solaris 8

Sparc Ultra2: Notes prtdiag: System Configuration: Sun Microsystems sun4u Sun Ultra 2 UPA/SBus (2 X UltraSPARC-II 296MHz) System clock frequency: 99 MHz Memory size: 768 Megabytes ========================= CPUs ========================= Run Ecache CPU CPU... (0 Replies)
Discussion started by: tnorth
0 Replies

4. Solaris

sun ultra or sun sparkstation

am wonder wich sun computer is better, a sun ultra or sun sparkstation, and what is the difference (7 Replies)
Discussion started by: nobody
7 Replies

5. Solaris

sun ultra

Hi Guys, I have a 2nd hand Sun ultra-5, I wanted to know how to be able to run it as a normal window. I do not have any experience whatsoever with solaris/unix. Does anyone can give me a clue where to start. When I switch it goes to: unix console login: pa$$word: #UNIX sendmail : enable to... (0 Replies)
Discussion started by: lingosa
0 Replies

6. Solaris

hey i just got a Sun ultra 5!!!

now what do i do? im looking at it and i booted it after a bunch of code i got a line askign for the password i also downloaded solaris 10 any advice on how to install it? (36 Replies)
Discussion started by: russian460
36 Replies

7. Solaris

Sun Solaris Ultra 10 Not booting!

Hello I have Sun Ultra 10 with Solaris 7 installed on it. Sometimes back after that the machine use to get hang .Even after rebooting the system was not booting. I have manually switch on /off many times from the power board itself .Once in a while it use to boot .After... (12 Replies)
Discussion started by: turki_00
12 Replies

8. Solaris

SUN ULTRA 45 - Solaris

hi, my sun box hangs- KEYBOARD not found. Using hyper link it boots and then hangs without able to access or get ok promt ----SCREEN SHOT AS-------------------------------------------------- ˙Loading onboard drivers: ebus i2c i2c i2c ppm /ebus@1f,464000: flashprom rtc serial serial env-monitor... (2 Replies)
Discussion started by: mathav22
2 Replies

9. Solaris

Cannot install Sun Solaris 10 on Ultra 10

http://www.unix.com/images/smilies/mad.gif Hi, this is parameswar. I have two sun ultra 5/10 workstations processor is sparc IIi 440 and ram is 512 but without hard disk and cdrom so can i use seagate 40Gb and sony dvd writer which is presented in windows pc. Both are IDE cables. while I... (1 Reply)
Discussion started by: parameswar
1 Replies

10. Solaris

Sun Ultra 5 new user

Hi I have just acquired an Ultra 5. It has 256MB of memory and a 360Mhz Ultra IIi SPARC processor. So far, I have had some typical fun and games to get it working: - It had a dead NVRAM chip. I hacked it open and installed a CR2032. It looks suitably bodged up, but is working. I set the MAC... (8 Replies)
Discussion started by: _JonB_
8 Replies
FINSIO(4)						   BSD Kernel Interfaces Manual 						 FINSIO(4)

NAME
finsio -- Fintek LPC Super I/O driver SYNOPSIS
finsio0 at isa? port 0x4e DESCRIPTION
The finsio driver provides support for the Fintek F71805F, F71806F, F71862FG, F71872, F71882 and F71883 LPC Super I/O chips. Only the Hardware Monitor device is supported and it provides you to monitor the sensors through the envsys(4) API. The finsio Super I/O Hardware Monitor supports 15 sensors (this depends on the chip ID): Sensor Units Typical Use IN0 uV DC Internal 3.3Vcc IN1 uV DC Memory Vtt IN2 uV DC RAM Vcc IN3 uV DC Chipset V IN4 uV DC +5V IN5 uV DC +12V IN6 uV DC Vcc 1.5V IN7 uV DC Vcore IN8 uV DC Vsb IN9 uV DC Vbat (optional) Temp1 uK CPU Temperature Temp2 uK Motherboard Temperature Temp3 uK (undefined) Fan0 RPM CPU Fan Fan1 RPM User Fan1 Fan2 RPM User Fan2 SEE ALSO
envsys(4), envstat(8) HISTORY
The finsio driver first appeared in NetBSD 5.0. AUTHORS
The finsio driver was written by Geoff Steckel and Juan Romero Pardines. BSD
April 3, 2008 BSD
All times are GMT -4. The time now is 07:56 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy