Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: route add
Operating Systems AIX route add Post 41287 by davidg on Thursday 2nd of October 2003 01:16:49 AM
Old 10-02-2003
David yes , the server reboots everyday . Thanks.

OK, now we are talking. This shows you have not taken your new route in your start-up files. You can do this using smit or manualy editing your start-up files.
Using smit you can do it :

System Management --> Communications App and Serv. --> TCP/IP --> Further Config --> Add a Static Route

Good luck.

Regs David
 

10 More Discussions You Might Find Interesting

1. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies

2. HP-UX

Add Route on HP-UX v10.x, help.

Hi, My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13 I tried with: #route add 192.168.80.2 255.255.255.255 10.10.10.13 but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies

3. IP Networking

Route add probleme

I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system. The ip i am trying to get to is 172.16.4.48 I need to get to it via the hme1 interface. The vpn gateway has this ip 172.30.50.1 I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies

4. Solaris

Route Add

Hi, I am trying to add route command in Solaris 10 machine in the following fashion: route add -host 10.8.112.10 180.144.1.250 -interface lo0:1 this command fails with an error "lo0:1: bad value" I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies

5. IP Networking

route add

I have built a new linux server, via a iLo connection. and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty. Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies

6. Solaris

route add : network is unreachable

Hey Guys: I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1 add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies

7. Solaris

Add route to solaris10

Hi need to add 2 routes, one on each server. I know the route add comand but I have always been given the parameters to put in. I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ? In... (6 Replies)
Discussion started by: vettec3
6 Replies

8. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies

9. Solaris

Couldn't add route on Solaris 10

Hi Solaris Experts, I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node # netstat -rnv IRE Table: IPv4 Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies

10. IP Networking

Add explicit route

Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254 if not working, please try gateway through management port: 10.128.55.254 Just want to double confirm if this would be the correct command #route add -net 10.128.255.41/32 10.128.201.254 And if didnt work #route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies

LEARN ABOUT OSF1

smsd

smsd(8) 						      System Manager's Manual							   smsd(8)

NAME

       smsd - The SysMan Station daemon

SYNOPSIS

       /usr/sbin/smsd

OPTIONS

       Runs smsd as a daemon. This creates a separate process and redirects output to the smsd log files.

DESCRIPTION

       The  SysMan  Station  is  a  client-server  application consisting of a daemon (smsd) and the SysMan Station graphical user interface (sys-
       man_station(8)).  The SysMan Station provides the ability to monitor and manage a single system or a TruCluster system.	The smsd server is
       responsible for gathering system management data from the host and presenting that information to the SysMan Station client. SysMan Station
       management data is collected from the following sources: Desktop Management (DMI) - software related  management  data  Common  Hardware  -
       hardware related management data Event Management (EVM) - event data SMS data files - SMS configuration data

RESTRICTIONS

       You must have root privileges to run this command.

EXAMPLES

       The following example shows how to run the System Management Station daemon: /sbin/init.d/smsd start

FILES

       The SysMan Station daemon The directory containing SysMan Station data files SysMan Station log files

SEE ALSO

       Commands: sysman_station(8)

       System Administration

																	   smsd(8)
All times are GMT -4. The time now is 08:43 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy