10-02-2003
# netstat -rn
Routing tables
Destination Gateway Flags Refcnt Use Interface
Netmasks:
(root node)
(0)0 ff00 0
(0)0 ffff ff00 0
(root node)
Route Tree for Protocol Family 2:
(root node)
default 199.5.2.1 UG 0 0 en0
127 127.0.0.1 U 1 1 lo0
192.x.x 192.x.x.abc U 1 0 et0 (old ip of the server)
199.x.x 199.x.x.def U 7 2149 en0 (current ip)
(root node)
Route Tree for Protocol Family 6:
(root node)
(root node)
#
David yes , the server reboots everyday . Thanks.
10 More Discussions You Might Find Interesting
1. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
2. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
3. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
8. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT DEBIAN
xml::xpath::node
XPath::Node(3pm) User Contributed Perl Documentation XPath::Node(3pm)
NAME
XML::XPath::Node - internal representation of a node
API
The Node API aims to emulate DOM to some extent, however the API isn't quite compatible with DOM. This is to ease transition from XML::DOM
programming to XML::XPath. Compatibility with DOM may arise once XML::DOM gets namespace support.
new
Creates a new node. See the sub-classes for parameters to pass to new().
getNodeType
Returns one of ELEMENT_NODE, TEXT_NODE, COMMENT_NODE, ATTRIBUTE_NODE, PROCESSING_INSTRUCTION_NODE or NAMESPACE_NODE. UNKNOWN_NODE is
returned if the sub-class doesn't implement getNodeType - but that means something is broken! The constants are exported by default from
XML::XPath::Node. The constants have the same numeric value as the XML::DOM versions.
getParentNode
Returns the parent of this node, or undef if this is the root node. Note that the root node is the root node in terms of XPath - not the
root element node.
to_sax ( $handler | %handlers )
Generates sax calls to the handler or handlers. See the PerlSAX docs for details (not yet implemented correctly).
MORE INFO
See the sub-classes for the meaning of the rest of the API:
o XML::XPath::Node::Element
o XML::XPath::Node::Attribute
o XML::XPath::Node::Namespace
o XML::XPath::Node::Text
o XML::XPath::Node::Comment
o XML::XPath::Node::PI
perl v5.10.1 2003-01-26 XPath::Node(3pm)