10-01-2003
Hi,
This normaly only changes after a reboot. Not on any other ocasion. Does your server reboot every day? (uptime)
If so, it should be added in your boot-up files.
Performing a netstat -rn, what does it say ??
Hope to get some info.
Regs David
10 More Discussions You Might Find Interesting
1. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
2. HP-UX
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies
3. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hey Guys:
I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable
root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1
add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies
7. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
8. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
reboot(2) System Calls Manual reboot(2)
NAME
reboot - boot the system
SYNOPSIS
DESCRIPTION
causes the system to reboot. howto is a mask of reboot options (see specified as follows:
A file system sync is performed (unless
is set) and the processor is rebooted from the default device and file.
The processor is simply halted.
A sync of the file system is performed unless the flag is set. should be used with caution.
On systems with cellular architecture, all cells in the partition are
rebooted in order to reconfigure the stable complex configuration data. On systems with non-cellular architec-
ture, the default is A sync of the file system is performed unless the flag is set.
Shut down the system firmware to a "ready to reconfigure" state and do not
reboot. This option can be used only in combination with
A sync of the file system is not performed.
Unless the flag has been specified, reboot(2) unmounts all mounted file systems and marks them clean so that it will not be necessary to
run fsck(1M) on these file systems when the system reboots.
Only users with appropriate privileges can reboot a machine.
RETURN VALUE
If successful, this call never returns. Otherwise, a -1 is returned and is set to indicate the error.
ERRORS
fails if this condition is encountered:
[EPERM] The effective user ID of the caller is not a user with appropriate privileges.
DEPENDENCIES
The default file and device for is on the current root device.
AUTHOR
was developed by HP and the University of California, Berkeley.
SEE ALSO
reboot(1M), privileges(5).
reboot(2)