Sponsored Content
Full Discussion: route add
Operating Systems AIX route add Post 41138 by cubicle^dweller on Tuesday 30th of September 2003 03:18:56 AM
Old 09-30-2003
route add

Hello ,

We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...

#route add server.ip router.ip

after this the ping command works fine , i've checked /etc/hosts file for the ip's ... it seems ok . please advice .

Thanks
 

10 More Discussions You Might Find Interesting

1. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies

2. HP-UX

Add Route on HP-UX v10.x, help.

Hi, My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13 I tried with: #route add 192.168.80.2 255.255.255.255 10.10.10.13 but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable I tried with... (4 Replies)
Discussion started by: efrenba
4 Replies

3. IP Networking

Route add probleme

I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system. The ip i am trying to get to is 172.16.4.48 I need to get to it via the hme1 interface. The vpn gateway has this ip 172.30.50.1 I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies

4. Solaris

Route Add

Hi, I am trying to add route command in Solaris 10 machine in the following fashion: route add -host 10.8.112.10 180.144.1.250 -interface lo0:1 this command fails with an error "lo0:1: bad value" I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies

5. IP Networking

route add

I have built a new linux server, via a iLo connection. and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty. Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies

6. Solaris

route add : network is unreachable

Hey Guys: I am trying to add a route for assign a network interface to the traffic to/from a specific net, but allways to get the same system message : network is unreacheable root@ColectorDMSCNT # route add net 200.44.46.0/24 161.196.84.196 1 add net 200.44.46.0/24: gateway... (2 Replies)
Discussion started by: aggadtech08
2 Replies

7. Solaris

Add route to solaris10

Hi need to add 2 routes, one on each server. I know the route add comand but I have always been given the parameters to put in. I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ? In... (6 Replies)
Discussion started by: vettec3
6 Replies

8. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies

9. Solaris

Couldn't add route on Solaris 10

Hi Solaris Experts, I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node # netstat -rnv IRE Table: IPv4 Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies

10. IP Networking

Add explicit route

Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254 if not working, please try gateway through management port: 10.128.55.254 Just want to double confirm if this would be the correct command #route add -net 10.128.255.41/32 10.128.201.254 And if didnt work #route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
defaultrouter(4)                                                   File Formats                                                   defaultrouter(4)

NAME
defaultrouter - configuration file for default router(s) SYNOPSIS
/etc/defaultrouter DESCRIPTION
The /etc/defaultrouter file specifies a IPv4 host's default router(s). The format of the file is as follows: IP_address ... The /etc/defaultrouter file can contain the IP addresses or hostnames of one or more default routers, with each entry on its own line. If you use hostnames, each hostname must also be listed in the local /etc/hosts file, because no name services are running at the time that defaultrouter is read. Lines beginning with the ``#'' character are treated as comments. The default routes listed in this file replace those added by the kernel during diskless booting. An empty /etc/defaultrouter file will cause the default route added by the kernel to be deleted. Use of a default route, whether received from a DHCP server or from /etc/defaultrouter, prevents a machine from acting as an IPv4 router. You can use routeadm(1M) to override this behavior. FILES
/etc/defaultrouter Configuration file containing the hostnames or IP addresses of one or more default routers. SEE ALSO
in.rdisc(1M), in.routed(1M), routeadm(1M), hosts(4) SunOS 5.10 17 Aug 2004 defaultrouter(4)
All times are GMT -4. The time now is 12:37 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy