Sponsored Content
Full Discussion: NIC cards for sunblade 100
Operating Systems Solaris NIC cards for sunblade 100 Post 40824 by TioTony on Tuesday 23rd of September 2003 11:40:48 PM
Old 09-24-2003
Hi Guys,
http://store.sun.com has more then you think. You can buy parts for all sorts of old Sun hardware, you just can't usually buy the entire system. I see several cards listed for the Blade 100 under the "Spare Parts" section of the store. We have purchased a few power supplies for Ultra 5's recently as we have been plaqued with several failures. The only issue is the cost. The power supplies aren't bad but things like CPUs cost several times more then a replacement box. Last I checked an Ultra 5/10 CPU was $1600. You can get 2 V100s for that price and they will be faster. Good luck with your parts,
TioTony
 

10 More Discussions You Might Find Interesting

1. IP Networking

Setup 2 NIC cards in one UNIX system

Hi; I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Discussion started by: texaspanama
2 Replies

2. High Performance Computing

veritas and nic cards

Hello I have 2 machines with 3 NIC cards. When I setup veritas, I receive this message: e1000g1 has an IP address configured on it. It could be a public NIC on ken. Are you sure you want to use e1000g1 for the first private heartbeat link? As if e1000g1 should not have an IP address.... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies

3. HP-UX

routing issues with multiple NIC cards

I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server) I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more. route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254 route add net 123.99.67.0 netmask... (2 Replies)
Discussion started by: myork
2 Replies

4. Red Hat

External NIC cards not pinging with each other in RHEL 5.1

We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and... (3 Replies)
Discussion started by: durgaprasadr13
3 Replies

5. Solaris

PC133 for sunblade 100

Greetings, I was in the mood of upgrading my sunblade100 in my bedroom, since I recuperated some RAM from intel servers, and found myself with what seems to not work (I was hoping to pass from 256Mb to 2GB... and then upgrading to solaris 10...) after this failure I tried with just one 512 MB,... (2 Replies)
Discussion started by: vbe
2 Replies

6. HP-UX

HP UX 9000 NIC CARDS

Hello, I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches. On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies

7. IP Networking

Best reference for understanding low level info on nic cards drivers and functionality

Hi, What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..? Thanks (2 Replies)
Discussion started by: Gopi Krishna P
2 Replies

8. Hardware

Nic Card for SunBlade 1500 Tower

Hi, I bought a server Sunblade 1500, and I would like to install a nic card. Anyone know any compatible network card for this server? Regards (1 Reply)
Discussion started by: ph0b0s
1 Replies

9. Ubuntu

Help asap squid with 2 nic cards setup

I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie.. Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Discussion started by: trilju2005
1 Replies

10. Ubuntu

How do you setup 2 nic cards for squid Ubuntu server?

I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table? I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
Ns_Url(3aolserver)					   AOLserver Library Procedures 					Ns_Url(3aolserver)

__________________________________________________________________________________________________________________________________________________

NAME
Ns_AbsoluteUrl, Ns_ParseUrl, Ns_RelativeUrl, Ns_SkipUrl - URL manipulation routines SYNOPSIS
#include "ns.h" int Ns_AbsoluteUrl(Ns_DString *pds, char *url, char *baseurl) int Ns_ParseUrl(char *url, char **pprotocol, char **phost, char **pport, char **ppath, char **ptail) char * Ns_RelativeUrl(char *url, char *location) char * Ns_SkipUrl(Ns_Request *request, int n) _________________________________________________________________ DESCRIPTION
Ns_AbsoluteUrl(pds, url, baseurl) Construct an URL based on baseurl but with as many parts of the incomplete url as possible. Return NS_OK or NS_ERROR. Ns_ParseUrl(url, pprotocol, phost, pport, ppath, ptail) Parse a URL into its component parts. Pointers to the protocol, host, port, path, and "tail" (last path element) will be set by ref- erence in the passed-in pointers. The passed-in url will be modified. Ns_RelativeUrl(url, location) If the url passed in is for this server, then the initial part of the URL is stripped off. e.g., on a server whose location is http://www.foo.com, Ns_RelativeUrl of "http://www.foo.com/hello" will return "/hello". Returns a pointer to the beginning of the relative url in the passed-in url, or NULL if error. Will set errno on error. Ns_SkipUrl(request, n) Return a pointer n elements into the request's url. SEE ALSO
nsd(1), info(n) KEYWORDS
AOLserver 4.0 Ns_Url(3aolserver)
All times are GMT -4. The time now is 09:40 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy