09-23-2003
Your best bet to ensure compatibility is to go to
http://store.sun.com and look up the available network cards for your system. You can also dig around Sunsolve.sun.com to find older part numbers. You can either buy them from Sun, a reseller, or some other 3rd party like Ebay. Although Sun uses PCI, not all PCI cards will work with Solaris.
10 More Discussions You Might Find Interesting
1. IP Networking
Hi;
I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Discussion started by: texaspanama
2 Replies
2. High Performance Computing
Hello
I have 2 machines with 3 NIC cards.
When I setup veritas, I receive this message:
e1000g1 has an IP address configured on it. It could be a public NIC on ken.
Are you sure you want to use e1000g1 for the first private heartbeat link?
As if e1000g1 should not have an IP address.... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies
3. HP-UX
I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server)
I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more.
route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254
route add net 123.99.67.0 netmask... (2 Replies)
Discussion started by: myork
2 Replies
4. Red Hat
We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and... (3 Replies)
Discussion started by: durgaprasadr13
3 Replies
5. Solaris
Greetings,
I was in the mood of upgrading my sunblade100 in my bedroom, since I recuperated some RAM from intel servers, and found myself with what seems to not work (I was hoping to pass from 256Mb to 2GB... and then upgrading to solaris 10...)
after this failure I tried with just one 512 MB,... (2 Replies)
Discussion started by: vbe
2 Replies
6. HP-UX
Hello,
I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches.
On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies
7. IP Networking
Hi,
What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..?
Thanks (2 Replies)
Discussion started by: Gopi Krishna P
2 Replies
8. Hardware
Hi,
I bought a server Sunblade 1500, and I would like to install a nic card. Anyone know any compatible network card for this server?
Regards (1 Reply)
Discussion started by: ph0b0s
1 Replies
9. Ubuntu
I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie..
Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Discussion started by: trilju2005
1 Replies
10. Ubuntu
I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table?
I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
DPT(4) BSD Kernel Interfaces Manual DPT(4)
NAME
dpt -- DPT RAID Controller SCSI driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device dpt
For one or more EISA cards:
device eisa
For one or more ISA cards:
device isa
For one or more PCI cards:
device pci
To allow PCI adapters to use memory mapped I/O if enabled:
options DPT_ALLOW_MEMIO
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
dpt_load="YES"
DESCRIPTION
The dpt driver supports DPT RAID SCSI controllers.
SmartRAID (PM3???) are "Enterprise" class cards, and SmartCache (PM2???) cards are in the "Workstation" class. The Gen 4 Smart Cache IV
products were a re-issue of the Gen 3 utilizing upgraded (and cheaper to produce) silicon. The PM3334 (Smart RAID III) was not revamped as
there was no upgraded silicon (68040 processor) and it was using the best DPT made. Note there has been customer confusion over the faster
enterprise class card supported by this driver being an older generation. The Gen5 cards are supported by the asr(4) driver.
HARDWARE
The dpt driver provides support for the following RAID adapters:
o DPT Smart Cache Plus
o Smart Cache II (PM2?2?, PM2022 [EISA], PM2024/PM2124 [PCI]) (Gen2)
o Smart RAID II (PM3?2?, PM3021, PM3222)
o Smart Cache III (PM2?3?)
o Smart RAID III (PM3?3?, PM3332 [EISA], PM3334UW [PCI]) (Gen3)
o Smart Cache IV (PM2?4?, PM2042 [EISA], PM2044/PM2144 [PCI]) (Gen4)
o Smart RAID IV
SEE ALSO
asr(4), cd(4), ch(4), da(4), sa(4), scsi(4)
HISTORY
The dpt driver first appeared in FreeBSD 2.2.6.
AUTHORS
The dpt driver was written by Simon Shapiro and ported to the CAM SCSI system by Justin T. Gibbs.
BSD
June 18, 2006 BSD