Sponsored Content
Full Discussion: NIC cards for sunblade 100
Operating Systems Solaris NIC cards for sunblade 100 Post 40735 by meyersp on Monday 22nd of September 2003 03:04:21 PM
Old 09-22-2003
NIC cards for sunblade 100

I need to add a PCI NIC to a sunblade 100 running solaris 8. Im new to this and was hoping someone could give me some card names and models which will work for this system and has a driver for this sparc system.

thanks
 

10 More Discussions You Might Find Interesting

1. IP Networking

Setup 2 NIC cards in one UNIX system

Hi; I have a UNIX box (SCO 5.0.2) with two (2) NIC cards. One card (NIC1) talks to a network 57.14.65.x/27. The other card NIC2) talks to users on 57.14.103.x and 57.14.105.x with subnet mask of 255.255.0.0. If I set NIC2 to this subnet mask (255.255.0.0) it seems like the NIC traffic is now... (2 Replies)
Discussion started by: texaspanama
2 Replies

2. High Performance Computing

veritas and nic cards

Hello I have 2 machines with 3 NIC cards. When I setup veritas, I receive this message: e1000g1 has an IP address configured on it. It could be a public NIC on ken. Are you sure you want to use e1000g1 for the first private heartbeat link? As if e1000g1 should not have an IP address.... (2 Replies)
Discussion started by: melanie_pfefer
2 Replies

3. HP-UX

routing issues with multiple NIC cards

I am running HP_UX 11.23 with 4 NIC cards (this is our TSM server) I have 4 subnets we are backing across. trying to keep traffic on their subnets. I only have one route statment should I add more. route add net 123.99.8.0 netmask 255.255.255.0 123.99.8.254 route add net 123.99.67.0 netmask... (2 Replies)
Discussion started by: myork
2 Replies

4. Red Hat

External NIC cards not pinging with each other in RHEL 5.1

We have a setup of two nodes which has two NIC cards in each. One is built in and another is D-Link (external NIC card). We are unable to ping to the external NIC cards in both. Eg: Node A has two IPs 192.168.1.10 (eth0) and 192.168.2.10 (eth1) and Node B has two IPs 192.168.1.20 (eth0) and... (3 Replies)
Discussion started by: durgaprasadr13
3 Replies

5. Solaris

PC133 for sunblade 100

Greetings, I was in the mood of upgrading my sunblade100 in my bedroom, since I recuperated some RAM from intel servers, and found myself with what seems to not work (I was hoping to pass from 256Mb to 2GB... and then upgrading to solaris 10...) after this failure I tried with just one 512 MB,... (2 Replies)
Discussion started by: vbe
2 Replies

6. HP-UX

HP UX 9000 NIC CARDS

Hello, I am trying to move an HP UX from one locaion to another. The new location don't have any Fiber switches. On the back of my server I see 2 RJ 45 for console management the other for networking , the server also has a fiber NIC card. When I disconnec the fiber and want to user regular... (1 Reply)
Discussion started by: ldaliosmane
1 Replies

7. IP Networking

Best reference for understanding low level info on nic cards drivers and functionality

Hi, What is the best reference that gives in detail on nic cards configuration , assigning multiple ip addresses to a single interface, netlink library etc and all basic stuff at this level..? Thanks (2 Replies)
Discussion started by: Gopi Krishna P
2 Replies

8. Hardware

Nic Card for SunBlade 1500 Tower

Hi, I bought a server Sunblade 1500, and I would like to install a nic card. Anyone know any compatible network card for this server? Regards (1 Reply)
Discussion started by: ph0b0s
1 Replies

9. Ubuntu

Help asap squid with 2 nic cards setup

I found an old post that talks about 2 nice cards and it is driven by the IP address .... but I didn't understand it because the 2 people skipped information for me the newbie.. Can someone help me... I have the proxy server setup and I believe I have enabled the 2nd nic card, I just need one... (1 Reply)
Discussion started by: trilju2005
1 Replies

10. Ubuntu

How do you setup 2 nic cards for squid Ubuntu server?

I have a made my squid proxy, I now have add another nic card to an old CPU using Ubuntu server 12.04. I have seen another post similar however I am new and did not understand some of it. Something about redirecting IP address and IP table? I don't know how to do this.:confused: (9 Replies)
Discussion started by: trilju2005
9 Replies
MY(4)							   BSD Kernel Interfaces Manual 						     MY(4)

NAME
my -- Myson Technology Ethernet PCI driver SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device my Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_my_load="YES" DESCRIPTION
The my driver provides support for various NICs based on the Myson chipset. The Myson chipset is a variant of the DEC Tulip NIC chipset. The driver will work with almost any MII-compliant PHY, thus failure to positively identify the chip is not a fatal error. HARDWARE
The my driver provides support for various NICs based on the Myson chipset. Supported models include: o Myson MTD800 PCI Fast Ethernet chip o Myson MTD803 PCI Fast Ethernet chip o Myson MTD89X PCI Gigabit Ethernet chip SEE ALSO
altq(4), de(4), netintro(4), pci(4), ifconfig(8) HISTORY
The my driver first appeared in FreeBSD 4.6. AUTHORS
The my driver was written by Myson Technology Inc. This manual page was written by Hiten M. Pandya <hmp@FreeBSD.org>. BUGS
The my driver does not support Power Management Events (PME). BSD
March 11, 2007 BSD
All times are GMT -4. The time now is 03:18 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy