09-17-2003
Preventing a scan of the RAID during bootup
I have a RH 7.3 server that needs a restart today after putting a patch in place. The last time I rebooted this box was almost a year ago and when the uptime is quite long, Linux likes to check all the disks for errors, including the RAID. This adds almost 1.5Hrs to my bootup process
.
Does anyone know a command/feature to turn off the scan before I shut down?
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi guys,
May I know how to install Solaris 8 in the way that I can triple boot it with my the other two OS: WIndows ME and Windows 2000 Pro.
Can you all please kindly advise me on how to setup the triple boot process inorder to allow Windows ME to be the default OS when being ask to choose... (1 Reply)
Discussion started by: cia
1 Replies
2. UNIX for Advanced & Expert Users
Hello there
I need to run a script whenever i reboot or startup my HP-UX server. This script adds some routes to the route table, and it start third party aplications like "Star Manager".
I thought i could do this simply putting the script in "/sbin/init.d,
and a link to the script in... (7 Replies)
Discussion started by: vascobrito
7 Replies
3. UNIX for Dummies Questions & Answers
Hi all
The following error was displayed when a sco server (5.0.5) was booted. What should be done to overcome the problem. Replies appreciated.
Bios 03.0
0130688 KB memory good
01 processor(s) in system
remote console dialing on, please wait
connect fail : modem off
cpu clock... (6 Replies)
Discussion started by: raguramtgr
6 Replies
4. UNIX for Dummies Questions & Answers
Evry time I start up my mavhine ,have to type in unix at
Boot
:
Is there a way unix should bootup automatically?
Asif (2 Replies)
Discussion started by: asif iqbal
2 Replies
5. UNIX for Dummies Questions & Answers
What is the boot up sequence in UNIX? (2 Replies)
Discussion started by: karthi_g
2 Replies
6. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT DEBIAN
raidfile-config
RAIDFILE-CONFIG(8) Box Backup RAIDFILE-CONFIG(8)
NAME
raidfile-config - Configure Box Backup's RAID files
SYNOPSIS
raidfile-config config-dir blocksize dir1 [dir2 [dir3]]
DESCRIPTION
raidfile-config creates a raidfile.conf file for Box Backup. This file holds information about the directories used to store backups in.
Box Backup supports userland RAID, in a restricted RAID5 configuration, where 3 and only 3 'drives' are supported. You can read more about
RAID5 (and other RAID-levels) here[1].
Parameters
The parameters are as follows:
config-dir
The directory path where configuration files are located. Usually this is /etc/box. raidfile.conf will be written in this directory.
blocksize
The block size used for file storage in the system, in bytes. Using a multiple of the file system block size is a good strategy.
Depending on the size of the files you will be backing up, this multiple varies. Of course it also depends on the native block size of
your file system.
dir1
The first directory in the built-in RAID array.
dir2
The second directory in the built-in RAID array. If you are not using the built-in RAID functionality, this field should be ignored.
You should not use the built-in RAID if you have a hardware RAID solution or if you're using another type of software RAID (like md on
Linux).
dir3
The third directory in the built-in RAID array. The same notes that apply to dir2 also apply to dir3.
Note that there are currently no way to add multiple disk sets to the raidfile.conf file using command line tools, etc. See
raidfile.conf(5) for details on adding more disks.
BUGS
If you find a bug in Box Backup, and you want to let us know about it, join the mailing list[2], and send a description of the problem
there.
To report a bug, give us at least the following information:
o The version of Box Backup you are running
o The platform you are running on (hardware and OS), for both client and server.
o If possible attach your config files (bbstored.conf, bbackupd.conf) to the bug report.
o Also attach any log file output that helps shed light on the problem you are seeing.
o And last but certainly not least, a description of what you are seeing, in as much detail as possible.
FILES
raidfile-config generates the raidfile.conf(5) file.
SEE ALSO
bbstored-config(8), bbstored.conf(5), raidfile.conf(5)
AUTHORS
Ben Summers
Per Thomsen
James O'Gorman
NOTES
1. here
http://en.wikipedia.org/wiki/Redundant_array_of_independent_disks#RAID_5
2. mailing list
http://lists.warhead.org.uk/mailman/listinfo/boxbackup
Box Backup 0.11 10/28/2011 RAIDFILE-CONFIG(8)