08-29-2003
setting a route in Solaris
I am having problems getting this to work, though it seems like it would be simple. I have a host with 2 interfaces, hme0 (192.168.0.132) for the primary interface, and hme1 (192.168.0.16) for backups. I want it to talk to the backup host, which is 192.168.0.21, across the hme1 interface.
Thanks
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hello Dear Friends, I'm here again
I need to know where is the permanent file for gateway configuration.
I did the following command
route add -net 0.0.0.0 5.0.0.3 ( My Gateway), but when i restart my computer i have to do it again.
What the file can i set the permanent configuration for my... (1 Reply)
Discussion started by: themask
1 Replies
2. IP Networking
WE are running Unix - Solaris 2.6, we create a subnet. In the windows enviroment we are able to add a static route by using
route add -p 172.16.10.0 mask 255.255.255.0 172.16.17.224, but when we add the route in Solaris as
route add -net 172.16.10.0 255.255.255.0 172.16.17.224, we receive an... (5 Replies)
Discussion started by: cassy
5 Replies
3. Solaris
hi,
i installed solaris 9 on an SPARC server with two network interfaces. behind each interface is a small lan. i can reach every computer in every lan using one of the other interface when i am logged in the solaris. but if a computer from one lan has to connect to a computer on the other lan,... (4 Replies)
Discussion started by: bong02
4 Replies
4. Solaris
I was told this worked on an HP system (same network as the sun server I am trying to set this up on)> but I get "netmask: bad value"2when I try it on the Sun:
route add net 199.42.23.192 netmask 255.255.255.192 204.104.63.30 1
I've tried many different iterations (leaving out netmask, only... (2 Replies)
Discussion started by: nhmeanie
2 Replies
5. Solaris
Hi,
Any one can help me in this below mentioned issue I am facing in my solaris server?
here the scenario goes....
i have multiple segments in my LAN like remote csr, database, production etc. and all the segments are configured in Windows/CISCo network.
from my all system in remote... (1 Reply)
Discussion started by: Praan
1 Replies
6. Solaris
Hi,
I am new to solaris 10. What is the procedure the os takes if a default route is not configured? I am using a multihomed server with 4 interfaces. It looked strange to me this morning, because i had not defined a default route it defaulted to making one up, with the ip address of another... (9 Replies)
Discussion started by: borderblaster
9 Replies
7. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
8. Solaris
Hi,
Every time when i boot my system i have to manually issue the following commands.
ifconfig elxl0 plumb 192.168.200.129 netmask 255.255.255.0 up
route add default 192.168.200.1
I need some help so that it should be configured permanently and i wouldn't have to manually issue... (2 Replies)
Discussion started by: malikshahid85
2 Replies
9. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
10. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
LEARN ABOUT DEBIAN
vde_tunctl
VDE_TUNCTL(8) System Manager's Manual VDE_TUNCTL(8)
NAME
vde_tunctl -- create and manage persistent TUN/TAP interfaces
SYNOPSIS
vde_tunctl [-f tun-clone-device] [-u owner] [-t device-name]
vde_tunctl [-f tun-clone-device] -d device-name
DESCRIPTION
vde_tunctl allows the host sysadmin to preconfigure a TUN/TAP device for use by a particular user. That user may open and use the device,
but may not change any aspects of the host side of the interface.
vde_tunctl is a simple copy of tunctl done for practical purposes.
USAGE
To create an interface for use by a particular user, invoke tunctl without the -d option:
# vde_tunctl -u someuser
Set 'tap0' persistent and owned by uid 500
Then, configure the interface as normal:
# ifconfig tap0 192.168.0.254 up
# route add -host 192.168.0.253 dev tap0
# bash -c 'echo 1 > /proc/sys/net/ipv4/conf/tap0/proxy_arp'
# arp -Ds 192.168.0.253 eth0 pub
To delete the interface, use the -d option:
# vde_tunctl -d tap0
Set 'tap0' nonpersistent
SEE ALSO
vde_switch(1) vde_plug2tap(1)
AUTHOR
tunctl was written by Jeff Dike jdike@karaya.com
This manual page is based on tunctl manual page written by Matt Zimmerman mdz@debian.org for the Debian GNU/Linux system.
VDE_TUNCTL(8)