07-11-2001
Solaris is sometimes tricky with broadcast addresses and configurable MAC addresses. I have spent hours on misconfigured Solaris ethernet interfaces. Sounds like you did a great job troubleshooting from your note. Please feel free to post again!
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
When using DHCP how can I can my hostname. I vi all the hosts file and if still didn't work. So now my hostname is unknown and I want to change it. So if anyone out there can help me. Thank You (6 Replies)
Discussion started by: aojmoj
6 Replies
2. UNIX for Advanced & Expert Users
Hi you all. I'm trying to enable DHCP in a Sun Utra 5 runing Solaris 8 but during the boot process it sends me the message : "Device not in appropiate status"
Do anyone have enabled DHCP on solaris 8?
Any Procedure?
The DHCP server is an NT I guess. (2 Replies)
Discussion started by: alex blanco
2 Replies
3. UNIX for Dummies Questions & Answers
HI,
New to Unix and I inherited a network that runs DHCP in manual configuration mode. Basically, in order for a machine to get an IP it has to have an entry in dhcpd.conf with its MAC address mapped to a hostname (the hostname then maps to an IP address listed in the DNS db file). If there is... (2 Replies)
Discussion started by: NJay
2 Replies
4. UNIX for Advanced & Expert Users
Last question for today!! :rolleyes:
In what file does the DHCP server keep its list of leases?
THANKS!!! :)
Maria from Maria (2 Replies)
Discussion started by: marjeg
2 Replies
5. Solaris
Can someone help me with this please. I am new to this:
I am trying to install Solaris 8 over the network using my DHCP. After I type the comman:
./add_install_client -d -e 8:0:20:7e:97:51
I would get something like this:
cleaning up preexisting install client "8:0:20:7e:97:51"... (0 Replies)
Discussion started by: aliban83
0 Replies
6. IP Networking
can I request for an ipaddress through dhcp client by sending ipaddress as input during the invokation of dhcpclient so that it requests the server for the same,instead of depending on the configuration file . (3 Replies)
Discussion started by: Gopi Krishna P
3 Replies
7. UNIX for Dummies Questions & Answers
Hi All,
I am trying to configure dhcp server on a linux host with eth0:1 which is using 192.168.1.10
I also want to restrict my DHCP client to just one Host adcnew222.
DHCP Server Host name - adcnew111
DHCP client name - adcnew222
My conf file is as follows on dhcp server :
... (2 Replies)
Discussion started by: sriram003
2 Replies
8. IP Networking
Dear Experts,
I have a TI DM8148 EVM board REV C, the EZSDK5.05 SW package, and DVRRDK1.09 SW package.
EZSDK5.05, DVRRDK1.09 both use Linux2.6.37, however, there are some modifications between these two kernels.
When I use uImage of DVRRDK1.09 to boot up EVM board, this board can be given a... (0 Replies)
Discussion started by: oobin168
0 Replies
9. IP Networking
Hi All ,
please view the set up below:
-------------------------------------------------------------------
| DHCP Server |-----------| ROUTER & |-----------| Clients |
| 192.168.99.1 | - -<eth1>| DHCP-RELAY|<eth2>-- | 192.168.88.X |
... (2 Replies)
Discussion started by: gdangoor
2 Replies
10. IP Networking
I have a DHCP thing on my HP printer. How can I find information on numbers for that? (2 Replies)
Discussion started by: teak
2 Replies
LEARN ABOUT SUSE
install-solaris
install-solaris(1M) install-solaris(1M)
NAME
install-solaris - install the Solaris operating system
SYNOPSIS
install-solaris
install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation,
install-solaris invokes either a text-based installer or a graphical installer.
The following minimum requirements for physical memory dictate which features are available during installation:
For SPARC machines:
128 MB
Minimum physical memory for all installation types
128 MB
Minimum physical memory required for windowing system
384 MB
Minimum physical memory required for graphical-based installation
For x86 machines:
256 MB
Minimum physical memory for all installation types
256 MB
Minimum physical memory required for windowing system
512 MB
Minimum physical memory required for graphical-based installation
In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea-
tures available.
install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more
details.
install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the
installation media. Refer to the for disk space requirements.
Refer to the for more information on the various menus and selections.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcdrom (Solaris instal- |
| |lation media) |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
pkginfo(1), install(1M), pkgadd(1M), attributes(5)
It is advisable to exit install-solaris by means of the exit options in the install-solaris menus.
23 Sep 2005 install-solaris(1M)