Sponsored Content
Full Discussion: PCMCIA problems
Top Forums UNIX for Dummies Questions & Answers PCMCIA problems Post 37380 by KrazyGuyPaul on Tuesday 17th of June 2003 06:49:47 PM
Old 06-17-2003
Data PCMCIA problems

Hi

I recently installed Mandrake 9 on my laptop. It has 2 PCMCIA slots, and in one of them I usually keep one of my network cards (ones an Accton 2216, the other a Surecom EP-427). Under mandrake when my computer started up (and went into runlevel 5) it attempted to start 'network' and then 'pcmcia'. Shortly after my keyboard and mouse went dead and I am forced to restart.

I am now running Red Hat 7.1 on the same computer. It boots just fine, because there is no PCMCIA service on startup. This is strange because before init starts (as its detecting hardware) I've seen it pick up the cards just fine. When X windows starts and I turn eth0 on, however, it doesn't seem to be able to communicate with the cards, saying "Startup delayed" (or something like that).

Does anyone have any suggestions as to what I should do so that I can use the cards? I would really appreciate it. Smilie

~ Paul
 

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

2.4.9 Linux Kernel & PCMCIA Wireless Problems

We are installing a PrismII chipset wireless PCMCIA card with a new 2.4.9 linux kernel. The card is a D-Link DWL-650. The 2.4.9 kernel uses the orinoco_cs.o driver. Anyone running this configuration? The 2.4.9 Linux kernel has built in PCMCIA support and the README says it supports the... (1 Reply)
Discussion started by: Neo
1 Replies

2. UNIX for Dummies Questions & Answers

PCMCIA Hardware Problem

Hi, I have a Dell Inspiron 4000 that I am using to run Redhat Linux 7.1. This machine had 128Mb of RAM in it, and I upgraded to 512Mb. Since this, the PCMCIA cards have disappeared from the system running under Linux, although they still work under windows and the file "/var/lib/pcmcia/stab"... (1 Reply)
Discussion started by: ghoti
1 Replies

3. UNIX for Dummies Questions & Answers

forcing irq on PCMCIA card

ENV: linux Version: Mandrake 8.1, PCMCIA card: longshine lcs-8534TB. (supported according the PCMCIA docs) laptop is P-II lifetec /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 ( found via probe -m ) PCIC_OPTS="cs_irq=11 pci_irq_list=11,11 do_scan=0" ( you see i want to force irq 11 )... (3 Replies)
Discussion started by: progressdll
3 Replies

4. UNIX Desktop Questions & Answers

How to configure Xircom pcmcia card to Red Hat 7.1?

I currently have an IBM Thinkpad with a built in 56k modem. RedHat 7.1 does not recognize my internal modem. I used a Xircom Ethernet 56 + 100 card. Linux knows the card is there. However, I have been unable to set it up. Please help is possible. (1 Reply)
Discussion started by: adrienb
1 Replies

5. UNIX for Dummies Questions & Answers

would like to purchase pcmcia modem that is supported by RedHat 7.3

I am using an IBM 390E laptop with a built-in LT modem which RH 7.3 does not notice. I would like to know if there are any pcmcia modems that are supported by version 7.3. If so, what is the propduct and where can I purchase it? Thanks!! adrienb:confused: (2 Replies)
Discussion started by: adrienb
2 Replies

6. UNIX for Dummies Questions & Answers

Solaris 8 and PCMCIA

Hi, I justed manged to install Solaris 8 on my Laptop, the only problem I have got is that It does not find my PCMCIA card. I need it to find my card so I can connect the Laptop to my LAN. I am using a 3Com LAN card model number is 3CCE589ET. This card work with Linux with no problems. ... (2 Replies)
Discussion started by: chamkila
2 Replies

7. UNIX for Dummies Questions & Answers

Error installing linksys pcm200 pcmcia card

Hi, I keep getting an error when I insert a pcm200 card on my laptop. The Error: Card type 32-bit cardbus is unsupported I am using freebsd 4.11 thanks lucky (2 Replies)
Discussion started by: luckyarab
2 Replies

8. UNIX for Advanced & Expert Users

Command to Analyze a PCMCIA Card

Is there a command that will verify what type of file system is located on a PCMCIA Card without having to mount the card? Thank you. (1 Reply)
Discussion started by: kilemark
1 Replies

9. BSD

PCMCIA-FreeBSD

Hi there. I have an old laptop Toshiba Tecra 510 (P1, 147MB RAM, 30GB HDD) and I installed FreeBSD 7.2. For networking I have a PCMCIA card for wired network. The problem is that I cannot start and run PCMCIA As I know in Linux there is a tool pcmciautils for this pc-cards, but in FreeBSD I have... (1 Reply)
Discussion started by: hirohitosan
1 Replies
GO-FISH(6)							 BSD Games Manual							GO-FISH(6)

NAME
go-fish -- play ``Go Fish'' SYNOPSIS
go-fish [-p] DESCRIPTION
go-fish is the game ``Go Fish'', a traditional children's card game. The computer deals the player and itself seven cards, and places the rest of the deck face-down (figuratively). The object of the game is to collect ``books'', or all of the members of a single rank. For example, collecting four 2's would give the player a ``book of 2's''. The options are as follows: -p Professional mode. The computer makes a random decision as to who gets to start the game, and then the computer and player take turns asking each other for cards of a specified rank. If the asked player has any cards of the requested rank, they give them up to the asking player. A player must have at least one of the cards of the rank they request in their hand. When a player asks for a rank of which the other player has no cards, the asker is told to ``Go Fish!''. Then, the asker draws a card from the non-dealt cards. If they draw the card they asked for, they con- tinue their turn, asking for more ranks from the other player. Otherwise, the other player gets a turn. When a player completes a book, either by getting cards from the other player or drawing from the deck, they set those cards aside and the rank is no longer in play. The game ends when either player no longer has any cards in their hand. The player with the most books wins. go-fish provides instructions as to what input it accepts. BUGS
The computer cheats only rarely. BSD
May 31, 1993 BSD
All times are GMT -4. The time now is 03:40 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy