Sponsored Content
Special Forums IP Networking RedHat and Ethernet card no like each other Post 37368 by Neo on Tuesday 17th of June 2003 04:10:52 PM
Old 06-17-2003
Here is the Linux driven for your platform:

http://h18000.www1.hp.com/support/fi...oad/16420.html

Here is another site that has it:

http://packages.debian.org/unstable/...00-source.html

Here is RedHat specfic info on your driver:

http://www.redhat.com/docs/manuals/l...-ethernet.html

PS: A google search with keywords:

Quote:
bcm5700 linux redhat
....yields lots of useful installation information..... Smilie
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies

3. UNIX for Dummies Questions & Answers

Ethernet card problem...

I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies

4. AIX

Add PCI ethernet card?

Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies

5. SCO

Issue with a ethernet card

Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message: Fsstat:/dev/boot mounted Mounted /stand filesystem System auditing is not enabled. Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0) Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies

6. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

7. Solaris

Ethernet card drivers issue...

I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do? Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies

8. AIX

Utilization of Ethernet Card

Hi, is it possible to find out network utilization of etherenet card in %? Regards, Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies

9. Linux

Offload parameters for Ethernet Card

Hi, Actually i want to see Offload parameter for my Eth card. Then after i try using this command Anybody can explain ? Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies

10. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
URI::URL(3)						User Contributed Perl Documentation					       URI::URL(3)

NAME
URI::URL - Uniform Resource Locators SYNOPSIS
$u1 = URI::URL->new($str, $base); $u2 = $u1->abs; DESCRIPTION
This module is provided for backwards compatibility with modules that depend on the interface provided by the "URI::URL" class that used to be distributed with the libwww-perl library. The following differences compared to the "URI" class interface exist: o The URI::URL module exports the url() function as an alternate constructor interface. o The constructor takes an optional $base argument. The "URI::URL" class is a subclasses of "URI::WithBase". o The URI::URL->newlocal class method is the same as URI::file->new_abs o URI::URL::strict(1) o $url->print_on method o $url->crack method o $url->full_path; same as ($uri->abs_path || "/") o $url->netloc; same as $uri->authority o $url->epath, $url->equery; same as $uri->path, $uri->query o $url->path and $url->query pass unescaped strings. o $url->path_components; same as $uri->path_segments (if you don't consider path segment parameters). o $url->params and $url->eparams methods. o $url->base method. See URI::WithBase. o $url->abs and $url->rel have an optional $base argument. See URI::WithBase. o $url->frag; same as $uri->fragment o $url->keywords; same as $uri->query_keywords; o $url->localpath with friends map to $uri->file o $url->address and $url->encoded822addr; same as $uri->to for mailto URI. o $url->groupart method for news URI. o $url->article; same as $uri->message SEE ALSO
URI, URI::WithBase COPYRIGHT
Copyright 1998-2000 Gisle Aas. perl v5.8.0 2002-05-09 URI::URL(3)
All times are GMT -4. The time now is 12:53 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy