06-17-2003
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT DEBIAN
ns_absoluteurl
Ns_Url(3aolserver) AOLserver Library Procedures Ns_Url(3aolserver)
__________________________________________________________________________________________________________________________________________________
NAME
Ns_AbsoluteUrl, Ns_ParseUrl, Ns_RelativeUrl, Ns_SkipUrl - URL manipulation routines
SYNOPSIS
#include "ns.h"
int
Ns_AbsoluteUrl(Ns_DString *pds, char *url, char *baseurl)
int
Ns_ParseUrl(char *url, char **pprotocol, char **phost,
char **pport, char **ppath, char **ptail)
char *
Ns_RelativeUrl(char *url, char *location)
char *
Ns_SkipUrl(Ns_Request *request, int n)
_________________________________________________________________
DESCRIPTION
Ns_AbsoluteUrl(pds, url, baseurl)
Construct an URL based on baseurl but with as many parts of the incomplete url as possible. Return NS_OK or NS_ERROR.
Ns_ParseUrl(url, pprotocol, phost, pport, ppath, ptail)
Parse a URL into its component parts. Pointers to the protocol, host, port, path, and "tail" (last path element) will be set by ref-
erence in the passed-in pointers. The passed-in url will be modified.
Ns_RelativeUrl(url, location)
If the url passed in is for this server, then the initial part of the URL is stripped off. e.g., on a server whose location is
http://www.foo.com, Ns_RelativeUrl of "http://www.foo.com/hello" will return "/hello". Returns a pointer to the beginning of the
relative url in the passed-in url, or NULL if error. Will set errno on error.
Ns_SkipUrl(request, n)
Return a pointer n elements into the request's url.
SEE ALSO
nsd(1), info(n)
KEYWORDS
AOLserver 4.0 Ns_Url(3aolserver)