06-17-2003
modprobe bcm5700
That may work^^, try it.
If you do not have this already (ie. if you get an error), download it from
this page of Asus' website.
Honestly that took me about 30 seconds to find
![Smilie Smilie](https://www.unix.com/images/smilies/smile.gif)
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT SUSE
web2disk
WEB2DISK(1) calibre WEB2DISK(1)
NAME
web2disk - part of calibre
SYNOPSIS
web2disk URL
DESCRIPTION
Where URL is for example http://google.com
Whenever you pass arguments to web2disk that have spaces in them, enclose the arguments in quotation marks.
OPTIONS
--version
show program's version number and exit
-h, --help
show this help message and exit
-d, --base-dir
Base directory into which URL is saved. Default is .
-t, --timeout
Timeout in seconds to wait for a response from the server. Default: 10.0 s
-r, --max-recursions
Maximum number of levels to recurse i.e. depth of links to follow. Default 1
-n, --max-files
The maximum number of files to download. This only applies to files from <a href> tags. Default is 9223372036854775807
--delay
Minimum interval in seconds between consecutive fetches. Default is 0 s
--encoding
The character encoding for the websites you are trying to download. The default is to try and guess the encoding.
--match-regexp
Only links that match this regular expression will be followed. This option can be specified multiple times, in which case as long
as a link matches any one regexp, it will be followed. By default all links are followed.
--filter-regexp
Any link that matches this regular expression will be ignored. This option can be specified multiple times, in which case as long as
any regexp matches a link, it will be ignored.By default, no links are ignored. If both --filter-regexp and --match-regexp are spec-
ified, then --filter-regexp is applied first.
--dont-download-stylesheets
Do not download CSS stylesheets.
--verbose
Show detailed output information. Useful for debugging
SEE ALSO
The User Manual is available at http://calibre-ebook.com/user_manual
Created by Kovid Goyal <kovid@kovidgoyal.net>
web2disk (calibre 0.6.53) July 2010 WEB2DISK(1)