|
|
Sponsored Content
Special Forums
IP Networking
RedHat and Ethernet card no like each other
Post 37331 by Tux on Tuesday 17th of June 2003 07:53:25 AM
06-17-2003
modprobe bcm5700
That may work^^, try it.
If you do not have this already (ie. if you get an error), download it from this page of Asus' website.
Honestly that took me about 30 seconds to find
That may work^^, try it.
If you do not have this already (ie. if you get an error), download it from this page of Asus' website.
Honestly that took me about 30 seconds to find
|
|
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT DEBIAN
acpi_asus
ACPI_ASUS(4) BSD/i386 Kernel Interfaces Manual ACPI_ASUS(4) NAME
acpi_asus -- Asus Laptop Extras SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file: device acpi_asus Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): acpi_asus_load="YES" DESCRIPTION
The acpi_asus driver provides support for the extra ACPI-controlled gadgets, such as hotkeys and leds, found on recent Asus (and Medion) lap- tops. It allows one to use the sysctl(8) interface to manipulate the brightness of the LCD panel and the display output state. Hotkey events are passed to devd(8) for easy handling in userspace with the default configuration in /etc/devd/asus.conf. Currently, the following Asus laptops are fully supported: xxN A1x A2x A3N A4D A6VM D1x J1x L2B L2D L2E L3C L3D L3H L4E L4R L5x L8x M1A M2E M6N M6R S1x S2x V6V W5A Eee PC Additionally, acpi_asus also supports the Asus-compatible ATK0100 interface found in Samsung P30/P35 laptops. SYSCTL VARIABLES
The following sysctls are currently implemented: hw.acpi.asus.lcd_brightness Makes the LCD backlight brighter or dimmer (higher values are brighter). hw.acpi.asus.lcd_backlight Turns the LCD backlight on or off. hw.acpi.asus.video_output Sets the active display to use according to a bitwise OR of the following: 0 No display 1 LCD 2 CRT 4 TV-Out Some models also support video switching via the generic acpi_video(4) driver. Most models do not, however. Defaults for these variables can be set in sysctl.conf(5), which is parsed at boot-time. SEE ALSO
acpi(4), acpi_video(4), sysctl.conf(5), sysctl(8) The acpi4asus Project, http://sourceforge.net/projects/acpi4asus/. HISTORY
The acpi_asus driver first appeared in FreeBSD 5.3. AUTHORS
The acpi_asus driver and this manual page were written by Philip Paeps <philip@FreeBSD.org>. Inspiration came from the acpi4asus project started by Julien Lerouge which maintains a driver implementing this functionality in the Linux kernel. BSD
December 17, 2008 BSD