06-16-2003
rebuild kernals, whoa now... lol
. I dont even know what a kernal is, let alone rebuild one (yes, I am another st00pid n00bie).
I think I might just do what norsk hedensk and you (neo) suggested and get a cheap network card. But how will I know that it will be compatible with linux? I might end up with another dud.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT DEBIAN
x86_64
SETARCH(8) System Administration SETARCH(8)
NAME
setarch - change reported architecture in new program environment and set personality flags
SYNOPSIS
setarch arch [options] [program [arguments]]
arch [options] [program [arguments]]
DESCRIPTION
setarch This utility currently only affects the output of uname -m. For example, on an AMD64 system, running 'setarch i386 program' will
cause 'program' to see i686 (or other relevant arch) instead of x86_64 as machine type. It also allows to set various personality options.
The default program is /bin/sh.
OPTIONS
-v, --verbose
Be verbose.
-h, --help
Display help (it is also displayed when setarch takes no arguments).
--uname-2.6
Causes the program to see a kernel version number beginning with 2.6.
-3, --3gb
Specifies that processes should use a maximum of 3GB of address space on systems where it is supported (ADDR_LIMIT_3GB).
-B, --32bit
Turns on ADDR_LIMIT_32BIT.
-F, --fdpic-funcptrs
Userspace function pointers point to descriptors (turns on FDPIC_FUNCPTRS).
-I, --short-inode
Turns on SHORT_INODE.
-L, --addr-compat-layout
Changes the way virtual memory is allocated (turns on the ADDR_COMPAT_LAYOUT).
-R, --addr-no-randomize
Disables randomization of the virtual address space (turns on ADDR_NO_RANDOMIZE).
-S, --whole-seconds
Turns on WHOLE_SECONDS.
-T, --sticky-timeouts
Turns on STICKY_TIMEOUTS.
-X --read-implies-exec
Turns on READ_IMPLIES_EXEC.
-Z, mmap-page-zero
Turns on MMAP_PAGE_ZERO.
EXAMPLES
setarch ppc32 rpmbuild --target=ppc --rebuild foo.src.rpm
setarch ppc32 -v -vL3 rpmbuild --target=ppc --rebuild bar.src.rpm
setarch ppc32 --32bit rpmbuild --target=ppc --rebuild foo.src.rpm
AUTHOR
Elliot Lee <sopwith@redhat.com>
Jindrich Novy <jnovy@redhat.com>
AVAILABILITY
The setarch command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
util-linux June 2007 SETARCH(8)