06-16-2003
aaah fudge, i quit
thanx for help. this is becoming too much for me
Last edited by Minnesota Red; 06-16-2003 at 11:27 PM..
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
PTS_QUIT(1) AFS Command Reference PTS_QUIT(1)
NAME
pts_quit - Exit from pts interactive mode
SYNOPSIS
pts quit [-cell] <cell name> [-noauth] [-localauth]
[-force]
pts q [-c] <cell name> [-n] [-l] [-f]
DESCRIPTION
The pts quit command exits from pts interactive mode. The command can be run from the command line or interactively, but on the command
line it does nothing and is therefore of questionable utility.
CAUTIONS
Prior to OpenAFS 1.4.5 and OpenAFS 1.5.23, the pts quit command was only available on Unix or Linux and when OpenAFS was compiled with the
supergroups option (disabled by default). As of OpenAFS 1.4.5 and 1.5.23, it is always available.
OPTIONS
Although they have no effect, pts quit takes the following standard pts options:
-cell <cell name>
Names the cell in which to run the command. For more details, see pts(1).
-force
Enables the command to continue executing as far as possible when errors or other problems occur, rather than halting execution at the
first error.
-help
Prints the online help for this command. All other valid options are ignored.
-localauth
Constructs a server ticket using a key from the local /etc/openafs/server/KeyFile file. Do not combine this flag with the -cell or
-noauth options. For more details, see pts(1).
-noauth
Assigns the unprivileged identity anonymous to the issuer. For more details, see pts(1).
OUTPUT
This command produces no output.
EXAMPLES
Here is an example of a pts interactive session:
% pts interactive
pts> quit
%
SEE ALSO
pts(1), pts_interactive(1)
COPYRIGHT
Copyright 2007 Jason Edgecombe <jason@rampaginggeek.com>
This documentation is covered by the BSD License as written in the doc/LICENSE file. This man page was written by Jason Edgecombe for
OpenAFS.
OpenAFS 2014-04-08 PTS_QUIT(1)