06-16-2003
redhat should auto detect it with no problem. what type of card is it? it is possible (though unlikley) that it is not supported. find out what driver to use for your card, and see the
ETHERNET HOW-TO
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem?
I am using the command:
ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up
I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies
3. UNIX for Dummies Questions & Answers
I am an extreme novice trying to learn Linux. I have redhat 9 installed in a computer I built specifically to install and learn linux. I have an asus a7v8x-x motherboard with the realtek 10/100 mbps ethernet card. I also installed a Jaht adapter jn-1110r32c ethernet card. I cannot get the... (2 Replies)
Discussion started by: Tony Empire
2 Replies
4. AIX
Hi everyone, I recently inherited an IBM RS/6000 43P 150, and it appears that the on board ethernet is dead. Can I put in a PCI ethernet card and use that as the default ethernet connection (as opposed to the one on the motherboard)? If so, what type of card can I use and how does one configure... (2 Replies)
Discussion started by: Jwoollard
2 Replies
5. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
6. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
7. Solaris
I need to install ethernet card drivers on intel machine. How can i know which Ethernet card interface (sfe,rh,rtls...) is it? How can i know the speed of that card? How can i know network traffic ? If network traffic is more with that interface what should i do?
Thanks in advance (2 Replies)
Discussion started by: younus_syed
2 Replies
8. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
9. Linux
Hi,
Actually i want to see Offload parameter for my Eth card.
Then after i try using this command
Anybody can explain ?
Is there any problem with my eth card ? (1 Reply)
Discussion started by: justbow
1 Replies
10. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
LEARN ABOUT CENTOS
opensc-tool
OPENSC-TOOL(1) OpenSC Tools OPENSC-TOOL(1)
NAME
opensc-tool - generic smart card utility
SYNOPSIS
opensc-tool [OPTIONS]
DESCRIPTION
The opensc-tool utility can be used from the command line to perform miscellaneous smart card operations such as getting the card ATR or
sending arbitrary APDU commands to a card.
OPTIONS
--atr, -a
Print the Answer To Reset (ATR) of the card. Output is in hex byte format
--card-driver driver, -c driver
Use the given card driver. The default is auto-detected.
--info, -i
Print information about OpenSC, such as version and enabled components.
--list-drivers, -D
List all installed card drivers.
--list-files, -f
Recursively list all files stored on card.
--list-readers, -l
List all configured readers.
--name, -n
Print the name of the inserted card (driver).
--reader num, -r num
Use the given reader number. The default is 0, the first reader in the system.
--send-apdu apdu, -s apdu
Sends an arbitrary APDU to the card in the format AA:BB:CC:DD:EE:FF....
--serial
Print the card serial number (normally the ICCSN). Output is in hex byte format
--verbose, -v
Causes opensc-tool to be more verbose. Specify this flag several times to enable debug output in the opensc library.
--wait, -w
Wait for a card to be inserted.
SEE ALSO
opensc-explorer(1)
opensc 06/17/2014 OPENSC-TOOL(1)