06-11-2003
You would do a
mount -t ufs /dev/hda* /mnt/somewhere
First check if UFS support is present with a
'cat /proc/filesystems' - if it isn't you need to load the kernel modules with 'insmod/modprobe ufs' (that's insmod, or modprobe)
Then check it is loaded with lsmod.
Then it's like mounting any other partition, specifying your filesystem with the -t flag.
If you forget where the partition is (it happens) you can do 'fdisk -l' although you probably knew that.
Viel Gluck.
Nope, i'm not german.
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi all, I have FreeBSD and Debian in my HD, the FreeBSD partition is very small and I'd like to change. I try to use partition magic but it does not work with UFS parition. Anyone know a good partition software? (1 Reply)
Discussion started by: SeVEn
1 Replies
2. UNIX for Dummies Questions & Answers
I am setting up a design tools server on a machine running Solaris9.
I want to setup a partition that contains a number of design tools.
If I go to / and type mkdir "tools" then I am on the root partition.
How do I get "/tools" to be on a separate partition?
(I also have the same problem... (2 Replies)
Discussion started by: smo59
2 Replies
3. OS X (Apple)
Hiya people..
I was hoping some expert here would share with me some details as I like to make a "System Recovery Partition" on a external drive. I use my MacBookPro on the road all the time and in the past it's known to happen, and often it happens at the worst time.
So, my question is: ... (0 Replies)
Discussion started by: Akira
0 Replies
4. Solaris
Hi there,
I am trying to mount a SAN volume (which is mapped to solaris sparc) partitioned with ufs filesystem onto a linux (intel processor 64bit) server.
*I have re-compiled the linux kernel t support ufs fstype with ro mount support.
filesystem on solaris:... (3 Replies)
Discussion started by: ilan
3 Replies
5. Solaris
OS: Solaris 10_x86.
Problem:
Server needs to be patched, but root "/" is near full.
/dev/dsk/c1t1d0s0 4.2G 3.9G 284M 94% /
The /exports/home dir has a lot more space, and I'd like to either move root "/" to it, or delete it all together:
/dev/dsk/c1t1d0s7 12G ... (20 Replies)
Discussion started by: b1f30
20 Replies
6. Solaris
Hi,
I have an application on a SAN partition presented to one server only. If I share this SAN partition with a second server as well, will that cause data corruption (the partition is formatted using ufs) ? (5 Replies)
Discussion started by: Mack1982
5 Replies
7. Solaris
Can anyone create a SPARC UFS Partition that is like 50 meg, DD the entire partition and zip it up and send it to me? Trying to play around with creating SPARC UFS partitions on linux and need a real one to compare to. I would do it but I do not have access to a SPARC machine anymore. I do not... (5 Replies)
Discussion started by: mooreps
5 Replies
8. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
LEARN ABOUT OPENSOLARIS
addpart
ADDPART(8) System Administration ADDPART(8)
NAME
addpart - tell the kernel about the existence of a partition
SYNOPSIS
addpart device partition start length
DESCRIPTION
addpart tells the Linux kernel about the existence of the specified partition. The command is a simple wrapper around the "add partition"
ioctl.
This command doesn't manipulate partitions on a block device.
PARAMETERS
device The disk device.
partition
The partition number.
start The beginning of the partition (in 512-byte sectors).
length The length of the partition (in 512-byte sectors).
SEE ALSO
delpart(8), fdisk(8), parted(8), partprobe(8), partx(8)
AVAILABILITY
The addpart command is part of the util-linux package and is available from https://www.kernel.org/pub/linux/utils/util-linux/.
util-linux January 2015 ADDPART(8)