06-03-2003
I would say yes although you might not notice it for some time and then only as a 'glich'.
See the
faq section on Ross-sparc processors - what you have isn't / wasn't a supported configuration but you may find you have no problems.
9 More Discussions You Might Find Interesting
1. UNIX Benchmarks
==============================================================
BYTE UNIX Benchmarks (Version 3.11)
System -- SunOS as-1 5.8 Generic_108528-24 sun4u sparc SUNW,UltraAX-i2
Start Benchmark Run: Tue Jan 27 15:07:18 NZDT 2004
3 interactive users.
Dhrystone 2 without register variables ... (0 Replies)
Discussion started by: mattd
0 Replies
2. Solaris
Hello all,
We have a group of Solaris 8 machines that are having some real network performance issues, they all go through a switch which *should* be set at 100 mb full duplex on every port which goes back to a master switch. I have checked the machines and the NIC cards are all set at 100 full.... (9 Replies)
Discussion started by: Mr Pink
9 Replies
3. AIX
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
Discussion started by: guttew
1 Replies
4. Red Hat
Hi,
what is command to find out no of core per procssor?
Regards,
Manoj (4 Replies)
Discussion started by: manoj.solaris
4 Replies
5. AIX
Guys...
Hows it going???
I have been going through the hardware spec of IBM system p systems.. and here i am confused
for IBM Power 520 Express it says
Processor cores:
One, two or four 64-bit 4.2 GHz POWER6 with AltiVec™ SIMD and Hardware Decimal Floating-Point acceleration
... (1 Reply)
Discussion started by: balaji_prk
1 Replies
6. Shell Programming and Scripting
How can I get the upload and download speed of my pc, provided that my interface is wlan0?
I have though something like:
#!/bin/sh
ups=something
downs=somethingelse
echo "
Your current up speed is $ups
Your current down speed is $downs, but I have no idea how to get them?Are... (5 Replies)
Discussion started by: hakermania
5 Replies
7. UNIX for Dummies Questions & Answers
Hi Gurus
can I emulate solaris/sparc on virtualbox? Or other emulator to run solaris for sparc in my win7 PC?
regards,
Israel. (9 Replies)
Discussion started by: iga3725
9 Replies
8. UNIX for Dummies Questions & Answers
HI
We have been asked by our IT department to move from our current physical solution to a VM environment. I am not that clued up on VM.
I looked from some benchmark tests to run so i can see a comparison between our live and new VM we have been presented. Please see below for results.
To me the... (3 Replies)
Discussion started by: treds
3 Replies
9. UNIX for Beginners Questions & Answers
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
LEARN ABOUT LINUX
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)