05-27-2003
First, thank you for your reply. i check my netcard configure, it is set to full duplex£¡¡¡
9 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Sorry to keep bothering you guys like this with all these boring, related questions. But here's one that should be more readily answerable.
What command or file should i use to get the speed/data rate of a network link? This is the capacity speed for instance 10Mbps or 100 Mbps in the case of the... (2 Replies)
Discussion started by: mint1981
2 Replies
2. HP-UX
Hello,
can anyone tell me how to change network speed or duplex speed...don't understand the concept why that is imp when the server comes back up to check up on it.
Basically have to make sure that the setting from the orginial speed. (2 Replies)
Discussion started by: catwomen
2 Replies
3. UNIX for Advanced & Expert Users
Need to make a very fast file existence checker. Passing in 20-50K num of files
In the code below ${file} is a file with a listing of +20,000 files. test_speed is the script. I am commenting out the results of <time test_speed try>.
The normal "test -f" is much much too slow when a system... (2 Replies)
Discussion started by: nullwhat
2 Replies
4. Solaris
i have first server (sun solaris 5.10) for example X(172.x.x.x)
and i have second server (sun solaris 5.10) for example Y(192.x.x.x)
also we have 3 clients PC (windows XP)(172.x.x.x)
the X server connect to Y server and to clients PC
* who to know the network speed between X and Y
* who to... (1 Reply)
Discussion started by: anwar
1 Replies
5. Shell Programming and Scripting
I had written a perl script to compare two files: new and master and get the output of the first file i.e. the first file: words that are not in the master file
STRUCTURE OF THE TWO FILES
The first file is a series of names
ramesh
sushil
jonga
sudesh
lugdi
whereas the second file (could be... (4 Replies)
Discussion started by: gimley
4 Replies
6. Hardware
Dear all,
Would you know how to measure the max speed of a WIFI connection between a router and a laptop for instance?
Many thanks for your help!
Regards, (3 Replies)
Discussion started by: freddie50
3 Replies
7. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
8. Red Hat
Dear All,
I have an intel NUC running CentOS 7 and physically connected to my Netgear CBVG834G router.
They both have Gigabit Ethernet cards and supposedly a top notch network cable connecting the two devices.
But when I run ethtool the connection is only running at 100Mbit/s
What can I do... (3 Replies)
Discussion started by: freddie50
3 Replies
9. Solaris
I have "inherited" a OmniOS (illumos based) server.
I noticed rsync is significantly slower in respect to my reference, FreeBSD 12-CURRENT, running on exactly same hardware.
Using same hardware, same command with same source and target disks, OmniOS r151026 gives:
test@omniosce:~# time... (11 Replies)
Discussion started by: priyadarshan
11 Replies
AXGE(4) BSD Kernel Interfaces Manual AXGE(4)
NAME
axge -- ASIX Electronics AX88178A/AX88179 USB Gigabit Ethernet driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device xhci
device ehci
device uhci
device ohci
device usb
device miibus
device axge
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_axge_load="YES"
DESCRIPTION
The axge driver provides support for USB Gigabit Ethernet adapters based on the ASIX Electronics AX88179 USB 3.0 and AX88178A USB 2.0
chipsets.
The AX88179 and AX88178A contain a 10/100/1000 Ethernet MAC with a GMII interface for interfacing with the Gigabit Ethernet PHY.
These devices will operate with both USB 1.x and USB 2.0 controllers, and the AX88179 will operate with USB 3.0 controllers. Packets are
received and transmitted over separate USB bulk transfer endpoints.
The axge driver supports the following media types:
autoselect Enable autoselection of the media type and options. The user can manually override the autoselected mode by adding media
options to rc.conf(5).
10baseT/UTP Set 10Mbps operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.
100baseTX Set 100Mbps (Fast Ethernet) operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or
half-duplex modes.
1000baseT Set 1000Mbps (Gigabit Ethernet) operation (AX88178 only). The ifconfig(8) mediaopt option can also be used to select either
full-duplex or half-duplex modes.
The axge driver supports the following media options:
full-duplex Force full duplex operation.
half-duplex Force half duplex operation.
For more information on configuring this device, see ifconfig(8).
SEE ALSO
altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), rgephy(4), vlan(4), ifconfig(8)
HISTORY
The axge device driver first appeared in FreeBSD 10.1.
AUTHORS
The axge driver was written by Kevin Lo <kevlo@FreeBSD.org> and Li-Wen Hsu <lwhsu@FreeBSD.org>. This manual page was adapted by Mark
Johnston <markj@FreeBSD.org> from the axe(4) manual page.
BSD
November 22, 2013 BSD