05-17-2003
no wait, i have a linksys 4 port cable/dsl router and you dont haveto disable DHCP. just make sure that whatever ip address you assign does not fall into the 192.168.1.100/255 range. assign it 192.168.1.2 and increment from there so its easier to keep track of what has what. you can still use DHCP.
10 More Discussions You Might Find Interesting
1. Programming
What does this command exactly do
cc -static example.c (6 Replies)
Discussion started by: wojtyla
6 Replies
2. IP Networking
Hi,
I have a machine that sits on 10.2 network.
I need to ssh from this to another box that is on both 10.125 & 10.140 VLANs
what should I need to do?
Thanks! (3 Replies)
Discussion started by: chaandana
3 Replies
3. UNIX for Dummies Questions & Answers
Hi,
Request you to please tell me the command or the process to add the static route in redhat linux.
Thanks in Advance.
Regards
Arun (2 Replies)
Discussion started by: Arun.Kakarla
2 Replies
4. Shell Programming and Scripting
Hi all,
Sorry I make a mistake,the title should be "How to statistic the average value "
I do five times about "mv 123 to 456"
and do five times about "mv 456 to 123"
As we know,"time" can get the real usr sys value,
I want to get the average real,usr,sys of "mv 123 to 456" and "mv 456 to... (4 Replies)
Discussion started by: yanglei_fage
4 Replies
5. IP Networking
hello, i need help on setting my coyote linux, i've working on this for last 5 days, can't get it to work. I've been posting this message to coyote forum, and other linux forum, but haven't get any answer yet. Hope someone here can help me...... please see my attached picture first.
... (0 Replies)
Discussion started by: dlwoaud
0 Replies
6. Linux
I have some static library(libxxx.a libyyy.a).
And I want to generate my library(libzzz.a), libzzz.a will use libxxx.a and libyyy.a
I wan't my application only use libzzz.a, (means libzzz.a had include libxxx.a, libyyy.a), how can I do that? Thank you.
example:
I have zzz.c.
I do ... (4 Replies)
Discussion started by: freemagic
4 Replies
7. UNIX for Dummies Questions & Answers
Hey guys ,
YEs this is probably silly for most but i am new to this forum and solaris . i am curious to know if the ip address we have for our solaris server is static or dhcp . how can i tell ? will ifconfig -a tell me this ? or other commands?
Thanks in advance (1 Reply)
Discussion started by: xdrivex
1 Replies
8. Programming
I'm writing a program which uses curl to be run on Linux PCs which will be used by a number of different users. I cannot make the users all install curl on their individual machines, so I have tried to link curl in statically, rather than using libcurl.so. I downloaded the source and created a... (8 Replies)
Discussion started by: BrandonShw
8 Replies
9. Programming
Are the following equivalent?
static int df, dl, du, count;
static int df;
static int dl;
static int du;
static int count; (7 Replies)
Discussion started by: kristinu
7 Replies
10. Solaris
Hi,
Here is what I get within Solaris.
huamin@SOL11I:~$ ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
net0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2
inet 0.0.0.0 netmask... (24 Replies)
Discussion started by: HuaMin
24 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)
NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD
April 11, 1998 BSD