04-21-2003
already done that
I have already installed the drivers, but ti still won't reconize the tape library at all plus won't boot until I take the card out of the 60.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
2. Solaris
i took this Elite 3D M3 video card out of my Ultra 60 machine which was replaced with an M6. the card was working w/o issue in the Ultra 60. however, i'm getting no video when i power the Tatung machine.
yes, the M3 is does work with an AXi motherboard. any ideas what's causing the problem? (1 Reply)
Discussion started by: xyyz
1 Replies
3. Solaris
I will be honest I am quite new to UNIX and Solaris so this may be a simple thing.
I have just purchased a Sun (rebranded HP obviously) DAT DDS3 SCSI tape drive for my Sun Ultra 10 running Solaris 10.
I have previously fitted a SCSI card to the box which has configured ok and can be seen from... (1 Reply)
Discussion started by: mattw
1 Replies
4. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
5. Solaris
is it possible to swap the Turbo XGX graphics card in the SS5 to the ULTRA server 1 ? and do they use the same type of RAM ?
Thx. (0 Replies)
Discussion started by: mads-nielsen
0 Replies
6. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
7. UNIX for Dummies Questions & Answers
i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me. (0 Replies)
Discussion started by: tatacoffee
0 Replies
8. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
9. Solaris
Guys,
I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem.
I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80.
I connected it powered it up and at OK prompt did : boot -r
system comes up and complains about not... (6 Replies)
Discussion started by: ajnabi
6 Replies
10. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
AHA(4) BSD Kernel Interfaces Manual AHA(4)
NAME
aha -- Adaptec SCSI host adapter driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device aha
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
aha_load="YES"
In /boot/device.hints:
hint.aha.0.at="isa"
DESCRIPTION
This driver provides access to the SCSI bus connected to the Adaptec AHA-154x and AHA-1640 SCSI host adapters. x is 0 for controllers with-
out a floppy drive and 2 for controllers that have them. For optimum performance, Adaptec AHA-174x controllers should be configured in
enhanced mode and attached via the ahb(4) driver.
One device hint entry for every card to be attached by the system is required. Specific values for the port address, IRQ, and DRQ may be
specified. If wildcard values are used, the driver will query the device for its current settings and use those. If the port address is a
wildcard, the driver consults an internal table of possible port address locations and attaches to the first unattached card it finds. The
possible port addresses for this card are 0x330, 0x334, 0x230, 0x234, 0x130, and 0x134.
The AHA-1640 is an MCA bus card. Since the MCA bus is a self-identifying bus, no setting of hints is required.
HARDWARE
The aha driver supports the following SCSI host adapters:
o Adaptec AHA-154xB
o Adaptec AHA-154xC
o Adaptec AHA-154xCF
o Adaptec AHA-154xCP
o Adaptec AHA-1640
o Adaptec AHA-174x in 154x emulation mode
o DTC 3290 SCSI controller in 1542 emulation mode
o Tekram SCSI controllers in 154x emulation mode
SEE ALSO
ahb(4), ahc(4), aic(4), cd(4), da(4), sa(4), scsi(4)
AUTHORS
The aha driver was ported by M. Warner Losh from the bt driver written by Justin T. Gibbs.
BUGS
The AHA-154xA card does not support residuals on data transfers. As a result, this card is no longer supported.
There have been some reports that the AHA-154xB does not work well under heavy load.
The AHA-154xCP is a plug and play controller. However, its resources are set using the on-board BIOS and cannot be moved. Failures to
attached for this card are often caused when the resources set in the BIOS conflict.
BSD
July 4, 2004 BSD