04-21-2003
already done that
I have already installed the drivers, but ti still won't reconize the tape library at all plus won't boot until I take the card out of the 60.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
HI,
I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors
genunix: NOTICE: glm0: fault detected in device; service still unavailable
genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported.
Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies
2. Solaris
i took this Elite 3D M3 video card out of my Ultra 60 machine which was replaced with an M6. the card was working w/o issue in the Ultra 60. however, i'm getting no video when i power the Tatung machine.
yes, the M3 is does work with an AXi motherboard. any ideas what's causing the problem? (1 Reply)
Discussion started by: xyyz
1 Replies
3. Solaris
I will be honest I am quite new to UNIX and Solaris so this may be a simple thing.
I have just purchased a Sun (rebranded HP obviously) DAT DDS3 SCSI tape drive for my Sun Ultra 10 running Solaris 10.
I have previously fitted a SCSI card to the box which has configured ok and can be seen from... (1 Reply)
Discussion started by: mattw
1 Replies
4. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
5. Solaris
is it possible to swap the Turbo XGX graphics card in the SS5 to the ULTRA server 1 ? and do they use the same type of RAM ?
Thx. (0 Replies)
Discussion started by: mads-nielsen
0 Replies
6. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
7. UNIX for Dummies Questions & Answers
i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me. (0 Replies)
Discussion started by: tatacoffee
0 Replies
8. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
9. Solaris
Guys,
I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem.
I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80.
I connected it powered it up and at OK prompt did : boot -r
system comes up and complains about not... (6 Replies)
Discussion started by: ajnabi
6 Replies
10. Solaris
I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
ALSACTL(1) General Commands Manual ALSACTL(1)
NAME
alsactl - advanced controls for ALSA soundcard driver
SYNOPSIS
alsactl [options] [store|restore|init] <card # or id or device>
DESCRIPTION
alsactl is used to control advanced settings for the ALSA soundcard drivers. It supports multiple soundcards. If your card has features
that you can't seem to control from a mixer application, you have come to the right place.
COMMANDS
store saves the current driver state for the selected soundcard to the configuration file.
restore loads driver state for the selected soundcard from the configuration file. If restoring fails (eventually partly), the init action
is called.
init tries to initialize all devices to a default state. If device is not known, error code 99 is returned.
If no soundcards are specified, setup for all cards will be saved or loaded.
OPTIONS
-h, --help
Help: show available flags and commands.
-d, --debug
Use debug mode: a bit more verbose.
-v, --version
Print alsactl version number.
-f, --file
Select the configuration file to use. The default is /etc/asound.state.
-F, --force
Used with restore command. Try to restore the matching control elements as much as possible. This option is set as default now.
-g, --ignore
Used with store and restore commands. Do not show 'No soundcards found' and do not set an error exit code when soundcards are not
installed.
-P, --pedantic
Used with restore command. Don't restore mismatching control elements. This option was the old default behavior.
-I, --no-init-fallback
Don't initialize cards if restore fails. Since version 1.0.18, alsactl tries to initialize the card with the restore operation as
default. But this can cause incompatibility with the older version. The caller may expect that the state won't be touched if no
state file exists. This option takes the restore behavior back to the older version by suppressing the initialization.
-r, --runstate
Save restore and init state to this file. The file will contain only errors. Errors are appended with the soundcard id to the end
of file.
-R, --remove
Remove runstate file at first.
-E, --env #=#
Set environment variable (useful for init action or you may override ALSA_CONFIG_PATH to read different or optimized configuration -
may be useful for "boot" scripts).
-i, --initfile #=#
The configuration file for init. By default, PREFIX/share/alsa/init/00main is used.
FILES
/etc/asound.state (or whatever file you specify with the -f flag) is used to store current settings for your soundcards. The settings
include all the usual soundcard mixer settings. More importantly, alsactl is capable of controlling other card-specific features that
mixer apps usually don't know about.
The configuration file is generated automatically by running alsactl store. Editing the configuration file by hand may be necessary for
some soundcard features (e.g. enabling/disabling automatic mic gain, digital output, joystick/game ports, some future MIDI routing options,
etc).
SEE ALSO
amixer(1), alsamixer(1), aplay(1)
BUGS
None known.
AUTHOR
alsactl is by Jaroslav Kysela <perex@perex.cz> and Abramo Bagnara <abramo@alsa-project.org>. This document is by Paul Winkler
<zarmzarm@erols.com>.
15 May 2001 ALSACTL(1)