Sponsored Content
Full Discussion: Ultra 3 scsi card
Top Forums UNIX for Advanced & Expert Users Ultra 3 scsi card Post 35597 by aojmoj on Monday 21st of April 2003 09:39:14 AM
Old 04-21-2003
Network Ultra 3 scsi card

Ok guys I need all the help I can get right now. I have a Ultra 60 sun server and I can't get a ultra 3 scsi card to work in it . When I install the card the system will not boot correctly and I come up with errors that say:

pcipsy0: This is block

Can someone please help me. I trying to hook up a tape library and it being very painful
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

SCSI Card in Solaris 8

HI, I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors genunix: NOTICE: glm0: fault detected in device; service still unavailable genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported. Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies

2. Solaris

problems with my M3 video card and my Tatung Ultra 10 clone

i took this Elite 3D M3 video card out of my Ultra 60 machine which was replaced with an M6. the card was working w/o issue in the Ultra 60. however, i'm getting no video when i power the Tatung machine. yes, the M3 is does work with an AXi motherboard. any ideas what's causing the problem? (1 Reply)
Discussion started by: xyyz
1 Replies

3. Solaris

Problem with SCSI DAT drive on Ultra 10

I will be honest I am quite new to UNIX and Solaris so this may be a simple thing. I have just purchased a Sun (rebranded HP obviously) DAT DDS3 SCSI tape drive for my Sun Ultra 10 running Solaris 10. I have previously fitted a SCSI card to the box which has configured ok and can be seen from... (1 Reply)
Discussion started by: mattw
1 Replies

4. SCO

configure Adaptec 29320ALP Ultra 320 SCSI Card in IBM X3400

I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies

5. Solaris

Sparcstation 5 graphics card in Ultra 1 server

is it possible to swap the Turbo XGX graphics card in the SS5 to the ULTRA server 1 ? and do they use the same type of RAM ? Thx. (0 Replies)
Discussion started by: mads-nielsen
0 Replies

6. SCO

ultra 320 scsi raid controller driver for sco 5.0.6

I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller . how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6. Plz help with any idea karzon (1 Reply)
Discussion started by: karzon
1 Replies

7. UNIX for Dummies Questions & Answers

installing scsi card

i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me. (0 Replies)
Discussion started by: tatacoffee
0 Replies

8. UNIX for Dummies Questions & Answers

Problems with SCSI card and tape drive

Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies

9. Solaris

Connect an External SCSI Hard Drive to Ultra 80

Guys, I have googled and checked this forum in detail and couldn't find any satisfactory answers for my problem. I am trying to connect a external SCSI hard Drive(Sea Gate) to a Ultra 80. I connected it powered it up and at OK prompt did : boot -r system comes up and complains about not... (6 Replies)
Discussion started by: ajnabi
6 Replies

10. Solaris

Solaris 10 SCSI card question

I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies
CARD(1) 								FSF								   CARD(1)

NAME
card - print reference card of program options SYNOPSIS
card [OPTION]... PROGRAM... DESCRIPTION
Print a reference card of the PROGRAMs thanks to their inline help. OPTIONS
-h, --help display this help and exit -v, --version display version information and exit -o, --output=FILE save the output in FILE -l, --language=LL print the help in the language LL (default: English) --command=CMD perform pretty-printing on the output of CMD (e.g. --command='netscape -help') Options for a2ps are given after `--', for instance $ card -lfr a2ps -- -Pdisplay -4 News, updates and documentation: http://www.inf.enst.fr/~demaille/a2ps/ AUTHOR
Written by Akim Demaille. REPORTING BUGS
Report bugs to <bug-a2ps@gnu.org>. COPYRIGHT
Copyright (C) 1997-99 Akim Demaille, Miguel Santana This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICU- LAR PURPOSE. SEE ALSO
a2ps(1), card(1), fixps(1), pdiff(1), psset(1), texi2dvi4a2ps(1). The full documentation for card is maintained as a Texinfo manual. If the info and card programs are properly installed at your site, the command info card should give you access to the complete manual. card 1.3 (GNU a2ps 4.13) July 2010 CARD(1)
All times are GMT -4. The time now is 07:18 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy