02-21-2003
Sun Sparc 20 Jumpstart install :(
Hello,
I'm having all kinds of trouble jumpstarting some SS20's.
After hunting around the newsgroups I find that this seems to be a fairly common problem with no real answer.
Here's a brief:
SS20, 50mhz, 256mb blah blah. - Client
E250 blah blah - J/start server.
10/100bt Network.
Setup the usual j/start bits for the client and do a 'boot net - install w' on the SS20.
Then all I get is 'Lost carrier- cable probs'.
Now I know for a fact the J/start stuff works a treat as I can do U1/2/5/60's no problem all day long.
I've tried setting the link-test-tpe to false, I've tried doing a 'boot net-tpe' etc.. But it just seems to ignore the fact its on a working network.
It will boot the net device and do its 'count' then it will start the arp/rarp errors, and link down stuff.
I can snoop it and find that the SS20 picks up it 'ip' etc, and does some packet exchanges.
AND just sometimes it will give losts of above errors, but still gradually start the install. But this is not very often.
Has any old school Solaris peeps out there ever solved this one!?
Thanks
John
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
In a single jumpstart server config using the initial_install option:
Can you jump x86 systems from a sparc platform? and/ or the opposite?
Or do you need a x86 and a SPARC box with an image on each? (6 Replies)
Discussion started by: BG_JrAdmin
6 Replies
2. Solaris
Hi ,
could you please clarify me the difference between sun sparc 32-bit and sun sparc 64-bit?
means on which processors these are supporting (pentium processors, sun sparc processors)
Regards,
Rajesh (1 Reply)
Discussion started by: pmrajesh21
1 Replies
3. Solaris
Can I use a Jumpstart enviroment on x86 to install a sparc64 client?
The idea is to install Solaris in an virtual environment (Sun Virtual Box) running on a pc (AMD), configure a Jumpstart server, and have a SUN Ultra 60 (sparc64) installed via the Jumpstart server.
The SUN has no cdrom... (4 Replies)
Discussion started by: eldiablo
4 Replies
4. Solaris
Hi,
I' trying to install O/S 5.9 on Sparc system Sunfire 280R. I downloaded CD install and CD 2 from Sun Website but later i dowloaded CD 2 that i forgot for my installation. All CD are in ISO formats.
I boot system at OK prompt then issue
OK boot cdrom
when it asks for CD 1, i removed... (7 Replies)
Discussion started by: lamoul
7 Replies
5. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
6. Solaris
Hello,
I'm trying to jumpstart a machine with Solaris 10, however the disks in my machine are only 18GB, but I want to have all the developer packages but none of the X windows stuff that can be quite large.
Wondered if it was possible to somehow get a list of all packages and remove the ones... (4 Replies)
Discussion started by: Actuator
4 Replies
7. Solaris
Hi all,
I have application running on sun server T5440 4x8x1.4 GHz, 64 GB RAM, application running very slow though load average too low. when I install my application on another server SUN M3000 (One CPU 1x8x2.5GHz, 8GB RAM), application run smoothly.
Here is my server T5440 info:
... (6 Replies)
Discussion started by: insatiable1610
6 Replies
8. Solaris
Dear all!
I've received 4 servers Sparc T4-2 on a rack, those servers was built in Solaris 11 ZFS bundled. Our Application is not coporated with the Sun 11, so, I must reinstall them.
However, whenever I ran cdrom in "ok prompt> bood cdrom", I received the line "Can not load cdrom". Recheck... (9 Replies)
Discussion started by: trantuananh24hg
9 Replies
9. Solaris
I've followed a few guides and have what appears to be a working jumpstart server. I can PXE boot a bare system, it gets an IP and launches the installer. However, it takes me to the screen:
SunOS Release 5.10 Version generic-147148-26 64 bit
Copyright (c) 1983, 2013, Oracle and/or its... (1 Reply)
Discussion started by: jnojr
1 Replies
10. UNIX for Beginners Questions & Answers
-> start /SYS
Are you sure you want to start /SYS (y/n)? y
Starting /SYS
]-> show HOST
/HOST
Targets:
bootmode
diag
domain
Properties:
autorestart = reset
autorunonerror = false
bootfailrecovery = poweroff
... (29 Replies)
Discussion started by: z_haseeb
29 Replies
LEARN ABOUT DEBIAN
pygm2n
pygm2n(1) Python Gateway mail to news pygm2n(1)
NAME
pygm2n - Python Gateway mail to news
SYNOPSIS
pygm2n -n newsgroups [ -s newsserver ] [ -h ]
DESCRIPTION
IMPORTANT: this man page is to be continued. The Whole pyg gateway is in devel. state. try -h option for more detailed option.
pygm2n reads from stdin an email, sending it to newsgroups, a comma separated list without spaces of newsgroup names (at least one), rfc799
compliant.
If pygm2n reads from stdin a sigle line starting with /, it is considered an absolute path to a single-email mailbox, so pygm2n will open
and read it.
Note that now pyg can't read a real mailbox, with many emails. If you give it in input, pyg will post the whole mailbox as a single email.
EXAMPLES
There is some documetation in /urs/share/doc/pyg
I created mailgate user (moderator of local.moderated ng). Subscribe to a list with this user (or simply email one message to). Every
email posted to this user will send to newsgroups, in its .procmailrc I've put something like:
:0 bh * ^From *mailinglist-request@lists.debian.org | $HOME/pygm2n -n local.debian.mailinglist
AUTHORS
Cosimo Alfarano <alfarano@students.cs.unibo.it>
BUGS
Boh. send any bug, advice or opinion to the author, please.
Sun Sep 12 18:10:00 CEST 2000 pygm2n(1)