Sponsored Content
Full Discussion: Solaris boot issues
Top Forums UNIX for Advanced & Expert Users Solaris boot issues Post 34271 by Perderabo on Thursday 13th of February 2003 09:32:35 AM
Old 02-13-2003
Regarding the first question, you need to do a reset or a power cycle to make the change take effect. From the ok prompt, just type "reset".

I never heard of creator3d or elitem6, so I'll pass on question 2.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

boot issues...

hardware on my first FreeBSD server has crashed. i was planning on swapping the HD into another machine, booting the generic kernel and then custom tailoring it to the new machine specs. however, i'm having a problem. the new machine is using a promise ultra100 card. i don't have any... (2 Replies)
Discussion started by: xyyz
2 Replies

2. Solaris

solaris boot problem boot error loading interpreter(misc/krtld)

When I installed the SOLARIS 10 OS first time, the desktop would not start up, this was because of network setup. Reinstalled worked. After a week due to some problem I had to reinstall OS, installation went fine and but when i reboot I get this error. cannot find mis/krtld boot error loading... (0 Replies)
Discussion started by: johncy_j
0 Replies

3. Solaris

V1280 boot issues

I have a client with a V1280 onsite and it is having boot problems. Below is the message it is returning when trying to boot. Is this something that anybody has run into, or that you might be able to shed some light on? {0} ok boot /ssm@0,0/pci@18,700000/ide@3/cdrom@0,0:f SunOS Release 5.9... (3 Replies)
Discussion started by: xcwhitex
3 Replies

4. SCO

xp/sco 5.0.7 dual boot issues

Hello those more knowledgeable than I: I have been trying to get xp and SCO to coexist on the same system. I have tried several different ways to make both work, here's the list: -install xp, image it, move the partition to the end of drive, verify it boots, image again, -boot off of SCO... (6 Replies)
Discussion started by: stay0ut
6 Replies

5. Solaris

Windows,Solaris, Red Hat triple boot issues

I have a pentium IV with 512 MB ram and 80 GB HDD. I first installed windows XP on the first primary partition, then Solaris on the second with 20 GB for the solaris partition, and when rebooted , the grub menu functioned as expected giving me the options to dual boot, so next I wanted to install... (3 Replies)
Discussion started by: saagar
3 Replies

6. Solaris

Boot issues Solaris 10 + V440

Hello, I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message: Sun Fire V440, No Keyboard Copyright 2007 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.22.33, 8192 MB... (14 Replies)
Discussion started by: stoci
14 Replies

7. Solaris

WAN boot Server issues.

I 'm trying to configure a WAN boot server on Solaris10 x86 for sparc clients .. when i try to set up the server m getting following error ./setup_install_server -w /var/apache2/htdocs/wanboot10/wpath /var/apache2/htdocs/wanboot10/ipath ERROR: Cannot make WAN boot Image file on this... (6 Replies)
Discussion started by: fugitive
6 Replies

8. Solaris

Solaris x86 installation using jumpstart does not local boot ( boot from hdd)

I am trying to install Solaris x86 using the Jumpstart server. I run the add_install_client command with appropriate options, and reboot my x86 Target box. The installation starts fine and unattended. After the installation completes and the target goes for a re-boot, it does not boot from the HDD... (9 Replies)
Discussion started by: hemalsid
9 Replies

9. Solaris

Solaris stuck during boot after reconfigure boot

Hello, I have a problem with my machine that won't boot properly. The story is that I installed a software called apcupsd, which is a control application for my APC battery UPS. I have used version 3.14.10 earlier, but as part of restoring my previously crashed os harddrive I wanted to... (18 Replies)
Discussion started by: Zorken
18 Replies

10. Red Hat

Boot Issues

I am installing Red Hat Linux 6.9 as a VM in Hyper-V on an HP laptop running Windows 10. After the install completes and the VM reboots, it gives me the message, "Detected CPU Family 6 model 142; Warning: Intel CPU model - this hardware has not undergone testing by Red Hat and might not be... (1 Reply)
Discussion started by: tigers580307
1 Replies
XkbSetAutoResetControls(3)					   XKB FUNCTIONS					XkbSetAutoResetControls(3)

NAME
XkbSetAutoResetControls - Changes the current values of the AutoReset control attributes SYNOPSIS
Bool XkbSetAutoResetControls (Display *dpy, unsigned int changes, unsigned int *auto_ctrls, unsigned int *auto_values); ARGUMENTS
- dpy connection to X server - changes controls for which to change auto-reset values - auto_ctrls controls from changes that should auto reset - auto_values 1 bit => auto-reset on DESCRIPTION
XkbSetAutoResetControls changes the auto-reset status and associated auto-reset values for the controls selected by changes. For any con- trol selected by changes, if the corresponding bit is set in auto_ctrls, the control is configured to auto-reset when the client exits. If the corresponding bit in auto_values is on, the control is turned on when the client exits; if zero, the control is turned off when the client exits. For any control selected by changes, if the corresponding bit is not set in auto_ctrls, the control is configured to not reset when the client exits. For example: To leave the auto-reset controls for StickyKeys the way they are: ok = XkbSetAutoResetControls(dpy, 0, 0, 0); To change the auto-reset controls so that StickyKeys are unaffected when the client exits: ok = XkbSetAutoResetControls(dpy, XkbStickyKeysMask, 0, 0); To change the auto-reset controls so that StickyKeys are turned off when the client exits: ok = XkbSetAutoResetControls(dpy, XkbStickyKeysMask, XkbStickyKeysMask, 0); To change the auto-reset controls so that StickyKeys are turned on when the client exits: ok = XkbSetAutoResetControls(dpy, XkbStickyKeysMask, XkbStickyKeysMask, XkbStickyKeysMask); XkbSetAutoResetControls backfills auto_ctrls and auto_values with the auto-reset controls for this particular client. Note that all of the bits are valid in the returned values, not just the ones selected in the changes mask. X Version 11 libX11 1.6.0 XkbSetAutoResetControls(3)
All times are GMT -4. The time now is 02:03 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy