12-15-2002
You need:
With SuSE 6.1
- 32 MB For Console
- 64 MB For X (Recommend)
With Mdk 9.0
- 32 MB For Console
- 128 MB For X (Recommend)
10 More Discussions You Might Find Interesting
1. Solaris
Hello,
This is my first post to this forum.
Recently I tried to install sun solaris 10 on my home pc.
But the installation failed due to not enough RAM.
I'm quite familiar with linux installation but this was my first with solaris.
Usually in these cases I would just install the bare... (9 Replies)
Discussion started by: ravinandan
9 Replies
2. HP-UX
HI all,
What the minimum & recommended system requirement for Rhel Linux to get install on it??:(
Plz reply ASAp (0 Replies)
Discussion started by: saurabh84g
0 Replies
3. AIX
HI all,
What the minimum & recommended system requirement for IBM AIX to get install on it??
Plz Reply ASAP. (3 Replies)
Discussion started by: saurabh84g
3 Replies
4. Red Hat
Hi,
On server 64bit Hw Arch , Linux 5.0(32bit) is installed it is showing only 3gb of ram though physical is 16gb
can u give me idea why? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
5. Shell Programming and Scripting
Hi there
I have generated a column containing 100.000 values. Sample:
94.971
101.468
73.120
100.601
102.329
I need to find the minimum value in this file and I must know which row it is in (no sorting).
I hope you can help!
Thanks! (16 Replies)
Discussion started by: cno
16 Replies
6. Shell Programming and Scripting
Hi All,
I have multiple files which contains 5 columns and multiple rows.....
I want to calculate the minimum value of column 5th, if column 2 is MET, till column 1 comes to the next number.
Also it must skip the condition similar to 1st line where column number 1 and 3 are same and... (9 Replies)
Discussion started by: CAch
9 Replies
7. Shell Programming and Scripting
Hi Friends,
my input file is this way
chr1 100 120 abc
chr1 100 121 def
chr1 100 122 ghi
chr2 240 263 kil
chr2 240 276 ghj
chr2 255 290 hjh
my output
chr1 100 122 abc
chr2 240 276 kil
chr2 255 290 hjh
Basically, I want to match on first and second column and then print the... (4 Replies)
Discussion started by: jacobs.smith
4 Replies
8. Shell Programming and Scripting
Hello,
I have this file file1.csv
Element1;23-10-2012;1,450;1,564;1,428
Element2;23-10-2012;1,448;1,565;1,427
Element3;23-10-2012;1,453;1,570;1,424
Element4;23-10-2012;1,428;1,542;1,405
Element5;23-10-2012;1,461;;1,453
Element6;23-10-2012;1,438;1,555;1,417... (6 Replies)
Discussion started by: saba01
6 Replies
9. Shell Programming and Scripting
input
1 2 3 4 5 2 8
2 1 1 1 4 2 1
5 4 4 4 2 1 3
2 2 6 7 4 5 4
5 5 5 4 3 3 5
I woud like to print a min of each row such that my output would look like
1
1
1
2
3 (5 Replies)
Discussion started by: johnkim0806
5 Replies
10. Programming
I have the following code and into into trying to simplifying it. Any suggestions please?
pmin = min (p(1), p(2), p(3), p(4), p(5), p(6))
ni = 0
xint = 0.0
yint = 0.0
zint = 0.0
!--------------------------------------------- !
if ((0.99999 * p(1)) <= pmin) then
... (3 Replies)
Discussion started by: kristinu
3 Replies
pdc(1M) pdc(1M)
NAME
pdc - processor-dependent code (firmware)
DESCRIPTION
is the firmware that implements all processor-dependent functionality, including initialization and self-test of the processor. Upon com-
pletion, it loads and transfers control to the initial system loader (isl(1M)). Firmware behavior varies somewhat, depending on the hard-
ware as described below.
To load from an external medium, must know the particular device on which resides. Typically the device is identified by the Primary Boot
Path that is maintained by in Stable Storage. A path specification is an I/O subsystem mnemonic that varies according to hardware model.
When the processor is reset after initialization and self-test complete, reads the Console Path from Stable Storage, and attempts to ini-
tialize the console device. If the initialization fails, attempts to find and initialize a console device. Algorithms used to find a con-
sole device are model-dependent. then announces the Primary Boot, Alternate Boot, and Console Paths.
If (see isl(1M)) is enabled, provides a 10-second delay, during which time the operator can override the sequence by typing any character
on the console. If the operator does not interrupt this process, initializes and reads from the Primary Boot Path. On models that support
autosearch, if this path is not valid and (see isl(1M)) is enabled, then searches to find a bootable medium.
If allowed to complete, a list of potentially bootable devices is displayed, labeled with abbreviated path identifiers (P0, P1, etc). A
simple menu is then displayed where the user can:
o Boot a specific device, using the abbreviated path identifier, or the full mnemonic.
o Start a device search where the contents are searched for IPL images (note the first search only identified devices and did not
check the contents).
o Enter the boot administration level.
o Exit the menu and return to autobooting
o Get help on choices
If the sequence is unsuccessful, overridden by the operator, or not enabled in the first place, interactively prompts the operator for the
Boot Path to use. Any required path components that are not supplied default to zero.
The Primary Boot, Alternate Boot, and Console Paths as well as and enable can be modified via
SEE ALSO
boot(1M), isl(1M).
PA-RISC Systems Only pdc(1M)