12-05-2002
Installing a SCSI controller... problems
Hi,
I have installed a SCSI Controller onto an HPUX 10.20b and I don't have any driver files for it when I check in Sys Admin. Do I need to update the kernel? I am not sure how to get the computer to recognize this controller... any suggestions?
Thanks
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
2. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
3. SCO
I am facing a problem to install sco 5.0.6 in Dell Power Edge SC1420 which raid controller is ultra 320 scsi raid controller .
how/from where to download the ultra 320 scsi raid controller driver for sco 5.0.6.
Plz help with any idea
karzon (1 Reply)
Discussion started by: karzon
1 Replies
4. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
5. UNIX for Dummies Questions & Answers
i hava bought scsi card for taking backup in a 12/24 DAT DRIVE -scounix5.05 i am havaing the cd of the same contain driver files how should i install it. can anybody help me. (0 Replies)
Discussion started by: tatacoffee
0 Replies
6. UNIX for Dummies Questions & Answers
Currenty running SCO Openserver 6 at a Dell PowerEdge T300. I recently installed a driver for an Adaptec SCSI card (adpu320). When I connect a tape drive to it and re-start the system,it freezes and displays the following message: "WARNING: adpu320: Command timed out (ha= 4)" and the system... (2 Replies)
Discussion started by: RicardoM
2 Replies
7. Filesystems, Disks and Memory
I need to hook a tape library to my compy (tru64 versifon 4F) by way of SCSI.
I can get as far as plugging it in on my own.
Please help
Thanks (0 Replies)
Discussion started by: randUSR()
0 Replies
8. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
IDA(4) BSD Kernel Interfaces Manual IDA(4)
NAME
ida -- Compaq Intelligent Drive Array Controllers
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device scbus
device ida
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
ida_load="YES"
DESCRIPTION
The Compaq Intelligent Drive Array (IDA) technology is used to distribute data across an array of hard drives. It unites these hard drives
into one or more high-performance logical drives. The drive array is managed by an array controller.
These controllers have the ability to provide fault tolerance for the connected drives and optionally provide write cache for the logical
drives. It is also possible for an application to access the SCSI bus subsystem directly by using the pass-through interface.
HARDWARE
The following controllers are supported by the ida driver:
o Compaq SMART Array 221
o Compaq Integrated SMART Array Controller
o Compaq SMART Array 4200
o Compaq SMART Array 4250ES
o Compaq SMART 3200 Controller
o Compaq SMART 3100ES Controller
o Compaq SMART-2/DH Controller
o Compaq SMART-2/SL Controller
o Compaq SMART-2/P Controller
o Compaq SMART-2/E Controller
o Compaq SMART Controller
IMPLEMENTATION NOTES
Extreme caution should be exercised when using the pass-through interface. It is possible to interfere with normal system I/O and cause
hangs if pass-through is used to an active device. Pass-through should only be used to a device that is otherwise quiescent.
SEE ALSO
cam(4), pass(4), xpt(4), camcontrol(8)
AUTHORS
The ida driver was written by Jonathan Lemon <jlemon@FreeBSD.org> and Matthew N. Dodd <mdodd@FreeBSD.org>. This manual page was written by
Tom Rhodes <trhodes@FreeBSD.org>.
BSD
August 8, 2004 BSD